Zinc, Paint & Accessories - Paynes Marine Group
Zinc, Paint & Accessories - Paynes Marine Group
Zinc, Paint & Accessories - Paynes Marine Group
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
728<br />
<strong>Zinc</strong>, <strong>Paint</strong> & <strong>Accessories</strong><br />
Pro<strong>Marine</strong>r<br />
CORROSION WORKBOOK<br />
• Take the guesswork out of corrosion control.<br />
Written for the non-technical person, this<br />
book answers questions and corrects misunderstandings about<br />
galvanic corrosion<br />
• Our portable Corrosion Test Meter and this book are all you need to<br />
solve corrosion problems on any vessel<br />
• Within one hour, this easy to understand workbook will enable you to<br />
perform corrosion surveys<br />
20001<br />
Pro<strong>Marine</strong>r<br />
SHAFt BRUSH<br />
Provides connection for prop shafts, rudder shafts, flywheels, etc.<br />
with ship's bonding system. Can eliminate radio frequency noise<br />
from rotating shafts and machinery. Long wearing metallic graphite<br />
bush on phosphor bronze strap. 12" L x 1" W.<br />
20035<br />
Pro<strong>Marine</strong>r<br />
YACHt CORROSION MONItOR<br />
• Instantly identifies adequate protection or<br />
damaging corrosion voltages<br />
• Simple yellow and green scale monitors<br />
voltage<br />
• Best for salt water use<br />
20030<br />
Pro<strong>Marine</strong>r<br />
CORROSION<br />
tESt MEtERS<br />
ANALOg tESt MEtER<br />
• Best for salt water use. This easy to read meter reads all corrosion<br />
problems instantly<br />
• Green=good, yellow=bad, scale needs no interpretation<br />
20006PRO<br />
Pro<strong>Marine</strong>r<br />
DIgItAL tESt MEtER<br />
• Highly sensitive digital meter for all<br />
types of water<br />
• Can also be used for testing D.C.<br />
volts, A.C. volts, continuity, diodes,<br />
resistance and up to 10 amps<br />
amperage<br />
60016PRO<br />
Pro<strong>Marine</strong>r<br />
PROSAFE FAILSAFE gALVANIC ISOLAtORS<br />
ProSafe FS installs easily and does not require a dedicated monitor to<br />
verify the operational status of the galvanic isolator as required by non<br />
FailSafe Certified galvanic isolators.<br />
ProSafe FS 30 & 60 are built on robust FlatPack semiconductor<br />
platforms ensuring that in the event of a failure, the failure is safe by not<br />
compromising the ground continuity on-board when connected to AC<br />
Shore Power.<br />
22034 Shore cord inlet<br />
compatibility Single 15, 16, 20 or 30<br />
size L x W x H 6.75” x 7” x 2.5”<br />
22074 Shore cord inlet Single 50 or Dual 15’s, 16’s,<br />
compatibility 20’s or 30’s<br />
size L x W x H 7.25” x 6.5” x 3.75”<br />
Pro<strong>Marine</strong>r<br />
PROSAFE<br />
gALVANIC ISOLAtORS<br />
Interrupts galvanic circuit with other boats and the dock when your boat<br />
is plugged into a shore power system. Maintains AC safety ground and<br />
solves the most common cause of corrosion. Protects against zinc loss.<br />
ProSafe consists of the galvanic isolator, the monitoring electronics and<br />
a remote display.<br />
• On-board automated test, monitoring and annunciation of ProSafe<br />
Galvanic Isolator operation and protection<br />
• On-board automated test, monitoring and annunciation of shore<br />
station AC ground wire presence and operation<br />
• On-board automated indication of AC shore power polarity<br />
22088 50 amp single / 30 amp dual AC line system<br />
22033 30 amp galvanic isolator<br />
Marinco<br />
gALVANALERt<br />
SHORE POWER CORROSION DEtECtOR<br />
GALVANALERT easily attaches to your existing 30a shore power inlet<br />
and cordset to constantly monitor if there is unsafe corrosion activity or<br />
if a reverse polarity condition exists – so you can act before serious and<br />
costly damage occurs to your boat.<br />
g30
Change language