Guide

Recommendations

Info

Table 1: Parameter Default Values Menu Parameter TigerStop TigerFence/ TigerCrossCut TigerTurbo Heavy Duty 2 TigerRack Motion Menu In Speed 25.000 5.000 35.000 35.000 25.000 Out Speed 25.000 5.000 35.000 35.000 25.000 In Accel 75.000 10.000 50.000 50.000 50.000 Out Accel 75.000 10.000 50.000 50.000 50.000 In Decel 75.000 10.000 50.000 50.000 50.000 Out Decel 75.000 10.000 50.000 50.000 50.000 Move 0ms 0ms 0ms 0ms 0ms Delay P Gain 2.000 4.000 2.000 2.000 2.000 I Gain 0.750 1.000 0.250 0.250 0.250 D Gain 20.000 25.000 6.000 6.000 6.000 Pd Gain 0.500 0.500 0.500 0.500 0.500 Pq Gain 0.500 .5 0.500 0.500 0.500 Id Gain 0.000 0 0 0 0 Iq Gain 0.000 0 0 0 0 Dither 50ms 50ms 4000ms 4000ms 4000ms Throttle 500 500 500 500 500 LVM Throttle 10000.010 10000.010 10000.010 10000.010 10000.010 LVB Throttle 325 325 325 325 325 HVM Throttle 5000.015 5000.015 15000.015 15000.015 15000.015 HVB Stall MEP 2.000 2.000 2.000 2.000 2.000 Stall MES 2.000 2.000 2.000 2.000 2.000 11
Table 1: Parameter Default Values Menu Parameter TigerStop TigerFence/ TigerCrossCut TigerTurbo Heavy Duty 2 TigerRack Motion Menu Timer Menu System Info Menu Run MEP 2.000 2.000 2.000 2.000 2.000 Run MES .200 .200 0.400 0.400 0.400 Break Vel 32.000 32.000 32.000 32.000 32.000 Break Gain 30.000 30.000 30.000 30.000 30.000 Find Vel 0.000 Find Trig 300.000 Clamp On Delay Saw On Delay DM Off Time Out TA On Time Out TA Off Time Out DM On Time Out Clamp Off Delay Saw Cycle Delay RDS Ready Time Out PET Delay Zero End TIK 100ms 100ms 5000ms 5000ms 5000ms 5000ms 100ms 100ms 2000ms 200ms Motor End None Baud Rate 57600 I/O Panel Baud Rate Motor Type 9600 Standard Rev Enc Depends on orientation Depends on orientation Depends on orientation Brake N/A N/A N/A N/A None 12
Page 1: Made In America 2015 TigerStop, LLC
Page 4 and 5: DANGER: This machine can start, mov
Page 6 and 7: The Home Routine When TigerStop is
Page 8 and 9: Basic Functions TigerStop has a few
Page 10 and 11: 3.Enter the number of the preset yo
Page 12 and 13: Menu The menu button is the gateway
Page 14 and 15: Table 1: Parameter Default Values M
Page 18 and 19: Table 1: Parameter Default Values M
Page 20 and 21: Note: It is important to re-measure
Page 22 and 23: 2.TigerStop will tell you that the
Page 24 and 25: Options Menu The options menu house
Page 26 and 27: Print Cut The print cut setting tel
Page 28 and 29: pattern parts lists. It also applie
Page 30 and 31: To change Load Offset... 1. Enter t
Page 32 and 33: Note: Take care when changing Opt S
Page 34 and 35: Banana 1 Banana 1 is a global param
Page 36 and 37: WidthCal WidthCal is used with Tige
Page 38 and 39: To change Out Acceleration... 1. En
Page 40 and 41: Note: Throttle LVM is a hidden sett
Page 42 and 43: Timer Menu The timer menu houses al
Page 44 and 45: 2. Enter the new Clamp Off Delay va
Page 46 and 47: Set Tool Interconnect Kit Set tool
Page 48 and 49: Laser Menu The laser menu houses al
Page 50 and 51: Crayon Crayon turns the TigerSaw 10
Page 52 and 53: Debug Menu The debug menu houses va
Page 54 and 55: Lists The list function is TigerSto
Page 56 and 57: Running a Pusher List 1.At the read
Page 58 and 59: 4.If you have the TigerStop optimiz
Page 60 and 61: Once the stock material is loaded,
Page 62 and 63: Editing a List 1.At the ready scree
Page 64 and 65: A Auto Detect 16 Auto Setup 15 Auto
Page 67:
FIND US ONLINE AT www.tigerstop.com
show all

Guide

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?