Guide

Recommendations

Info

pattern parts lists. It also applies to manual moves if an interconnect kit is installed. If TigerStop goes to a dimension smaller than the backoff value, TigerStop will back up to the backoff value and wait until the cut is complete. This is used to back out of the way of clamps or other devices. To change Backoff... 1. Enter the new backoff value. 2. Press the [Done] soft key to save the parameter. Retract The retract setting is a global parameter that applies to all push and pattern parts lists. It also applies to manual moves if an interconnect kit is installed. After TigerStop has moved to position, TigerStop will back up by the value of the retract setting and will wait for the tool to cycle before moving to the next position. To change Retract... 1. Enter the new retract value. 2. Press the [Done] soft key to save the parameter. Retract Offset The retract offset is a global parameter that works with the retract setting. At the end of a retract move, TigerStop will move forward to meet the part before it pushes to the next length. The retract offset offsets this movement by the settings value. This is used when the part moves after it is processed by the tool. To change Retract Offset... 1. Enter the new retract offset value. 2. Press the [Done] soft key to save the parameter. Retract Type Retract Type is a global parameter that works with the retract setting. It tells TigerStop when to apply the retract move to a pusher or pattern list. Retract Type Options Standard - The retract move will happen as soon as TigerStop moves material to position. DM Only - The retract move will happen as soon as the DM circuit opens. Note: DM Only mode is only usable with a Standard Interconnect Kit. To change Retract Type... 1. Press [B] or [C] to toggle the retract type setting. 2. Press the [Done] soft key to save the parameter. 23
Part List Menu The part list menu houses all the settings that control how a programed parts list runs. At the menu select screen, press the [PartList] soft key to access the Part List menu. Head Cut The head cut setting applies a global head cut to all push, pattern and pull part lists. A head cut is a trim cut at the beginning of the stock to remove potential defects. To change Head Cut... 1. Enter the new head cut value. 2. Press the [Done] soft key to save the parameter. Tail Cut The tail cut setting applies a global tail cut to all push, pattern and pull parts lists. A tail cut is a trim cut at the end of the stock to remove potential defects. To change Tail Cut... 1. Enter the new tail cut value. 2. Press the [Done] soft key to save the parameter. Outfeed The outfeed setting is a global parameter that applies to all push and pattern parts lists. After the last cut is made from the stock material, outfeed will send TigerStop past the zero point by the value of the setting. Note: Outfeed must be set to a negative value. To change Outfeed... 1. Enter the new outfeed value. 2. Press the [Done] soft key to save the parameter. Load Offset The load offset is a global parameter that applies to all push and pattern parts lists. Load offset will add to the load position to give the operator more room to load the stock when processing a pusher or pattern parts list. When using TigerSaw 1000 crayon marking system, load offset is the load position of the pusher foot before the defect scanning operation. 24
Page 1: Made In America 2015 TigerStop, LLC
Page 4 and 5: DANGER: This machine can start, mov
Page 6 and 7: The Home Routine When TigerStop is
Page 8 and 9: Basic Functions TigerStop has a few
Page 10 and 11: 3.Enter the number of the preset yo
Page 12 and 13: Menu The menu button is the gateway
Page 14 and 15: Table 1: Parameter Default Values M
Page 20 and 21: Note: It is important to re-measure
Page 22 and 23: 2.TigerStop will tell you that the
Page 24 and 25: Options Menu The options menu house
Page 26 and 27: Print Cut The print cut setting tel
Page 30 and 31: To change Load Offset... 1. Enter t
Page 32 and 33: Note: Take care when changing Opt S
Page 34 and 35: Banana 1 Banana 1 is a global param
Page 36 and 37: WidthCal WidthCal is used with Tige
Page 38 and 39: To change Out Acceleration... 1. En
Page 40 and 41: Note: Throttle LVM is a hidden sett
Page 42 and 43: Timer Menu The timer menu houses al
Page 44 and 45: 2. Enter the new Clamp Off Delay va
Page 46 and 47: Set Tool Interconnect Kit Set tool
Page 48 and 49: Laser Menu The laser menu houses al
Page 50 and 51: Crayon Crayon turns the TigerSaw 10
Page 52 and 53: Debug Menu The debug menu houses va
Page 54 and 55: Lists The list function is TigerSto
Page 56 and 57: Running a Pusher List 1.At the read
Page 58 and 59: 4.If you have the TigerStop optimiz
Page 60 and 61: Once the stock material is loaded,
Page 62 and 63: Editing a List 1.At the ready scree
Page 64 and 65: A Auto Detect 16 Auto Setup 15 Auto
Page 67: FIND US ONLINE AT www.tigerstop.com

Guide

Create successful ePaper yourself

Delete template?

Save as template?