Timken - Saf Split-Block Housed Units

More documents

Recommendations

Info

TIMKEN SHELF LIFE AND STORAGE OF GREASE-LUBRICATED BEARINGS AND COMPONENTS STORAGE Timken suggests the following storage guidelines for our finished products (bearings, components and assemblies, referred to as “products”): • Unless directed otherwise by Timken, products should be kept in their original packaging until they are ready to be placed into service. • Do not remove or alter any labels or stencil markings on the packaging. • Products should be stored in such a way that the packaging is not pierced, crushed or otherwise damaged. • After a product is removed from its packaging, it should be placed into service as soon as possible. • When removing a product that is not individually packaged from a bulk pack container, the container should be resealed immediately after the product is removed. 12 TIMKEN ® HOUSED UNIT CATALOG • Download 3D Models and 2D Drawings at cad.timken.com
TIMKEN SHELF LIFE AND STORAGE OF GREASE-LUBRICATED BEARINGS AND COMPONENTS • Do not use product that has exceeded its shelf life as defined in the Timken shelf life guidelines statement. • The storage area temperature should be maintained between 0° C (32° F) and 40° C (104° F); temperature fluctuations should be minimized. • The relative humidity should be maintained below 60 percent and the surfaces should be dry. • The storage area should be kept free from airborne contaminants such as, but not limited to, dust, dirt, harmful vapors, etc. • The storage area should be isolated from undue vibration. • Extreme conditions of any kind should be avoided. Due to the fact that Timken is not familiar with your particular storage conditions, we strongly suggest following these guidelines. However, you may be required by circumstances or applicable government requirements to adhere to stricter storage requirements. Most bearing components typically ship protected with a corrosion-preventive compound that is not a lubricant. These components may be used in oil-lubricated applications without removal of the corrosion-preventive compound. When using some specialized grease lubrications, we advise you to remove the corrosion-preventive compound before packing the bearing components with suitable grease. We pre-pack most housed unit types in this catalog with general-purpose grease suitable for their normal applications. It may be necessary for you to frequently replenish the grease for optimum performance. Be careful in selecting lubrication, however, since different lubricants are often incompatible. You may order housed units pre-lubricated with a specified lubrication. When you receive a bearing or housed unit shipment, do not remove products from their packaging until they are ready for mounting so they do not become corroded or contaminated. Store bearings and housed units in an appropriate atmosphere so they remain protected for the intended period. TIMKEN ® HOUSED UNIT CATALOG • Download 3D Models and 2D Drawings at cad.timken.com 13
Page 1: Timken ® SAF Split-Block Housed Un
Page 4 and 5: TIMKEN Overview GROW STRONGER WITH
Page 6 and 7: INTRODUCTION HOUSED UNIT OVERVIEW R
Page 8 and 9: INTRODUCTION HOUSED UNIT OVERVIEW T
Page 10 and 11: INTRODUCTION HOUSED UNIT OVERVIEW T
Page 12 and 13: TIMKEN How to use this catalog HOW
Page 16 and 17: TIMKEN warnings and Cautions WARNIN
Page 18 and 19: Timken ® SAF SPLIT-BLOCK HOUSED UN
Page 64 and 65:
Timken ® SAF SPLIT-BLOCK HOUSED UN
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126:
10M 12-14: 29 Order No. 10591 | Tim
show all

Timken - Saf Split-Block Housed Units

Create successful ePaper yourself

Delete template?

Save as template?