CP7372 - OE 80 - SF

104
Clutch - Carbon/Carbon
CP7923.
Ø140mm, 3 Plate, Heavy Duty Pull Type.
GENERAL INFORMATION
APPLICATIONS.
- GT.
- Endurance racing.
FEATURES.
- 10 Bolt, One piece cover and lugs.
- machined from solid billet, for
rigidity and strength.
- Pull type confi guration.
- increased effi ciency in terms of clamp and release loads.
- Heavy Duty version of CP7223 Clutch.
- Extra carbon plate, acts as heat shield to heavy duty
diaphragm spring.
- Flat fl ywheel fi xing.
- Cushion fl ywheel system available.
- Long Life.
- Durable and abuse resistant.
- If maintained correctly life expectancy can be 10 times that
of a sintered race clutch.
- Factory reconditioning service available.
PART NUMBERS.
- 3 Plate, Flat Flywheel.
CP7923-GH03-FN.
- 3 Plate, Flat Flywheel with CFS.
CP7923-GH03-FC.
Note: Full Installation Drawing available at
www.apracing,com
INSTALLATION DRAWING
73.70
RECOMMENDED FOR
# 10 MOUNTING HOLES
Ø6.012/6.000
EQUISPACED ON A
152.00 P.C.
OPTIONAL STARTER
RING GEAR.
SUPPLIED BY CUSTOMER
30.50 MAX
6.40 MIN
3.40 MIN
1.65 MIN
Ø34.25 MAX
45.00° MIN
##50.80
##34.79
DIRECTION OF
RELEASE TRAVEL
R6.30
6.20
60.00°
REF
GEAR RING
FORM
45.00° MIN
R5.75 MIN
10 COVER MOUNTING
HOLES Ø6.15/6.05
EQUISPACED ON A
152.00 P.C.
Ø39.00
RELEASE
FULCRUM
#R0.25
#1.00
RECOMMENDED CLUTCH
MOUNTING:
FOR ALL TYPES OF ASSEMBLY.
M6x1.0, Cp4703 FAMILY
STUD AND KLOCK NUT. NUTS
TO BE TIGHTENED IN A
DIAMETRICALLY-OPPOSITE
SEQUENCE,HALF A TURN AT
A TIME TIGHTENING TORQUE
10Nm (7.5lb/ft) LENGTH OF
STUD REQUIRED TO BE
CALCULATED THUS: DIMENSION
‘C’ + ‘F’ + (‘R’ OPTIONAL)+ NUT.
#162.08
162.04
5.00
Ø140mm Clutch
Torque
Capacity.
TECHNICAL SPECIFICATIONS
1333Nm (982lb/ft)
“Wear In”
between P/Plate changes.
1.50mm
Total allowable carbon stack
wear.
6.0mm
Release Loads.
Max peak
worn.
At
travel.
565daN
370daN
Set-up Height. (New) 45.35mm
Set-up Height. (Worn) 38.10mm
Weight. 2.75Kg
Complete
Assembly Inertia.
0.0102Kgm²
Driven Plate &
Hub Interia.
0.001348Kgm²
Ratio.
MAIN PRESSURE PLATES.
HiR
Material. Steel
.5mm to 4.5mm (0.5mm Steps) =
Pressure Plate
CP6504-7
Kits.
.25mm to 4.25mm (0.5mm Steps) =
CP6504-8
HUB OPTIONS.
Material. Steel
1.16” x 26 CP7803-108S
More hubs are available with other spline sizes, contact AP Racing.
SLAVE CYLINDER.
Recommended Slave Cylinder. CP6245-8
www.apracing.com +44 (0)24 7663 9595
57.90
57.20
Ø97.00
54.65
53.95
15.46
1.60
2.50
AXIAL FLOAT
Ø33.00
32.75
Ø34.975
34.960
Ø161.98
161.93
RELEASE
FULCRUM AND
CIRCLIP
SUPPLIED
Ø86.01
Ø162.06
161.86
THIS ASSEMBLY IS SUPPLIED NEW WITH AN INSTALLATION
PLATE AS SHOWN, THIS IS TO ALLOW THE ASSEMBLY TO BE
BOLTED TO THEFLYWHEEL WITHOUT DAMAGING ANY OF
THE CLUTCH COMPONENTS. AFTER BOLTING THE CLUTCH
TO THE FLYWHEEL REMOVE THE CIRCLIP AND INSTALLATION
PLATE AND RETAIN FOR USE WHEN REMOVING THE
ASSEMBLY FROM THE FLYWHEEL
NOTE WHEN REMOVING A
WORN CLUTCH ASSEMBLY
THE INSTALLATION PLATE IS
TO BE FITTED WITH THE WORN
CONDITION - THIS SIDE-UP
INSTRUCTION ON THE OUTSIDE.
WHEN RETURNING THIS CLUTCH
ASSEMBLY BACK TO AP
RACING FOR RECONDITIONING
PLEASE RETURN WITH THIS
INSTALLATION PLATE FITTED.
0.75x44.50 MIN
R1.50