Marca Model Difetto Cura Aim AR276 Stops aft 10 mins R443 6R8 ...
Marca Model Difetto Cura Aim AR276 Stops aft 10 mins R443 6R8 ...
Marca Model Difetto Cura Aim AR276 Stops aft 10 mins R443 6R8 ...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Ferguson FV<strong>10</strong>0 Noise bars on pic & whirr on sound in play Pinch roller had come apart & catching on housing<br />
cam follower peg snapped off (under mode motor gear ass'y) Pt No Lever Cam<br />
Ferguson FV<strong>10</strong>5 cassette housing failure<br />
70363446A<br />
Ferguson FV<strong>10</strong>B Dead - int blows mains fuse Resolder dry joints on IC801<br />
Ferguson FV<strong>10</strong>B Dead - no display R1 <strong>10</strong>R 1/2w in psu o/c<br />
Ferguson FV<strong>10</strong>B Jerky capstan int on play & Rec Capstan motor faulty<br />
Ferguson FV<strong>10</strong>B Wont accept tape - no drum -shows "cass in" symbol STK5481 chip<br />
Ferguson FV11 Display pulses rapidly C1 <strong>10</strong>0µ 63v; C5 47µ 63v (on main psu); C6/9/11 <strong>10</strong>µ 25v all esr ><strong>10</strong>0<br />
Ferguson FV11 Drum runs slow replace IC VC2023A<br />
Ferguson FV11 E -E ok Playback Sound ok but no picture just blank raster E -E 5V line always 5V Q503 DTC144W U/S<br />
Ferguson FV11 No capstan lock C24/25 4µ7 25v<br />
Ferguson FV11 No chan memorise when switched off Back up battery on front panel<br />
Ferguson FV11 No mechs No 5 or 12v o/p from STK5481 - chip u/s<br />
Ferguson FV11 No reel motor op Q605 2SC2560<br />
Ferguson FV11 Patterning - Herringbone on Pback - e-e ok C9 <strong>10</strong>µ 50v on Tuner/IF pcb (decouples 5v supply)<br />
Ferguson FV11 Patterning in playback esp when heated OK with the bottom removed! - IC1 5v reg near tuner<br />
Ferguson FV11R Display flickers<br />
Replaced following hi esr caps:- C1 <strong>10</strong>0µ 63v, C5 47µ 63v (both on tfmr pcb); C12 <strong>10</strong>0µ<br />
16v, C13 47µ 16c, C11 <strong>10</strong>µ 25v, C14 <strong>10</strong>0µ 16v, C<strong>10</strong> 47µ 25v. C6 <strong>10</strong>µ 50v, C9 <strong>10</strong>µ 50v<br />
Ferguson FV11R No capstan lock C24 & C25 4µ7 25v on servo pcb<br />
Ferguson FV11R No diplay - ok otherwise R4 ( 220ohm ) O/C<br />
Ferguson FV11R No tuning memory Varta 2.4v battery on front pcb<br />
Ferguson FV11R Poor pback - looks like worn heads 5v reg faulty<br />
Ferguson FV11R Powers up but no pback STK5481 chip<br />
Ferguson FV11R Won't accept tape - screeching noise Mode sw earth screw loose<br />
Ferguson FV12 E-E/Pback jumping & dist Change 7 electrolytics near IC<strong>10</strong>1- C123, C124, C130,C133, C134, C135, C137.<br />
Ferguson FV12L Laces up then stops - no capstan IC604 M54644BL drive chip<br />
Ferguson FV12L records in B & W only BPF302 filter o/c - vid feed to dec chip<br />
Ferguson FV14 Int stops with no capstan or drum op Dry joints pin 6 IC601 on mecha board - brown glue nearby<br />
Ferguson FV14T No sound e-e or pback on hifi sound posn Caused by brown gunge on FMA board<br />
Ferguson FV20 Fails to load cassette Right hand IR sensor o/c<br />
Ferguson FV20 Jammed tape & screeching mechs syscon micro faulty - expensive! - robbed from scrap machine<br />
Ferguson FV20 Loading motor screams at sw on & sw off Loading belt slipping - replaced<br />
Ferguson FV20 WON'T LOAD TAPES RH DECK END SENSOR OC<br />
Ferguson FV200LV Dead <strong>aft</strong>er storm DP056 BAV20 s/c in psu
Change language