Marca Model Difetto Cura Aim AR276 Stops aft 10 mins R443 6R8 ...

JVC HRJ425
broken tension spring fixing on front lever plate, under the cassette housing (on the
Won't accept or eject cassette - plays ok if wound in manually main deck).The spring is under the plate slightly to the left of centre
Replace the broken take-up lever ass'y (PQ21686-1-3) and the very blackened mode
JVC HRJ425EK No mechs
switch (PU61432-1-2).
JVC HRJ435 Dead Q902 2SC3616 s/c
JVC HRJ455EK NO DRUM ROTATION REPLACE CP4001 HRS*ICFN15
JVC HRJ507MS Powers up for a couple of secs then reverts to st/by Check cprots - CP801 F20 o/c (measure volts on R803 13.5v - if missing check cp)
Replace main slider & supply spool brakes on underside of mechs - it may appear to be
JVC HRJ600 Brakes not working when stopped after FFwd/Rew
unworn
JVC HRJ600 Dead Check C12 on psu pri - but D35 16v zener was s/c in this case
JVC HRJ600 Int failure to eject Damaged teeth relay gear & drive arm ass'y - replace & mode sw
JVC HRJ600 Very int locks up C608 back up capacitor dry jointed
JVC HRJ600 won't accept tape, faulty eject & noisy replace deck assy - pivot pin loose - Pt no PQ11473B-10 £25.91
JVC HRJ600 Wont eject fully pin on main deck - relay arm bearing faulty - replace main deck!
JVC HRJ600EK No drum CP40 N15 o/c - towards front of main pcb
JVC HRJ610 Dead C12, 38, 31, 41
JVC HRJ610 Int blanks out in e-e & rec Video muting tr being muted - C206 0µ1 50v low cap in IF unit
JVC HRJ610EK Blank screen in E-E - may be int C206 0µ1 50v in IF/det unit
JVC HRJ610EK Dead C12 2µ2 50v, C31 22µ 63v hi esr
JVC HRJ610EK Dead C12 2µ2 50v in psu pri also check caps in psu sec
JVC HRJ610EK Dead after mains interruption All elects in psu were hi esr
JVC HRJ610EK No E-E - pback ok No 12v to IF sect, Q2 2SB810 & check all caps in unit for hi esr
JVC HRJ615E Dead C12 2µ2 63v, C31 & C34 22µ 63v C38 0µ47 50v
JVC HRJ625 Eject fails - capst motor whirring Spring anchorage broken off change arm Item 74
JVC HRJ625 Eject inop
Int fails to load - when it happens, 1/2 load arm item 26 fails
Change arm ass'y broken peg releasing spring - SEME pt no VPAR7178
JVC HRJ625 to reach its end Load motor faulty
JVC HRJ625 int slack tape on eject cleaned mode sw
JVC HRJ625 No capst drive BU2884S driver chip
JVC HRJ625 No RF o/p Check RF out sw on rear of machine
JVC HRJ625 NOT LOADING TAPES IF CAPSTAN MOTOR NOT TURNING REPLACE IC401 (BU2884S)
JVC HRJ625 PSU squealing Mains cap 68µ 400v may be o/c & check other caps in psu
JVC HRJ625
HRJ625 (M
Wont accept tape Change arm ass'y & mode sw
JVC chassis) Cuts out on playback. Spindle of T/U reel slightly bent forward bent straight or replace the deck!
JVC HRJ625EK Mechs jammed Replace control plate, mode sw, control cam & realign