Marca Model Difetto Cura Aim AR276 Stops aft 10 mins R443 6R8 ...
Marca Model Difetto Cura Aim AR276 Stops aft 10 mins R443 6R8 ...
Marca Model Difetto Cura Aim AR276 Stops aft 10 mins R443 6R8 ...
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Ferguson TX92 low sound with background hiss <strong>aft</strong> storm micro needs setting up <strong>aft</strong>er standard changed to wrong system<br />
Fidelity VCR1600F Chews tapes Gear centre assy has cracks which can be seen when flexed VDC7720 from SEME<br />
Fidelity VCR2020F Won't accept tape & cass in symbol flashing Dry joints supply end sensor<br />
Q<strong>10</strong>01 (2SC4204) s/c (Note PCB markings WRONG!, Q<strong>10</strong>02 (2SC4517) s/c, R<strong>10</strong>14<br />
Fidelity VCR3000 Dead<br />
(1ohm) o/c, R<strong>10</strong>02 (4.7ohm) o/c. caused by secondary D<strong>10</strong>09 S/cct.<br />
Fidelity VCR4000 No take up Capstan belt pulley adrift of flywheel - can be glued back on<br />
Fidelity VCR4000 Noisy ffwd/rew Capstan motor us<br />
Fidelity VCR4000 Play goes fast int Capstan motor<br />
Finlux VR163NX Dead Mains bridge cap <strong>10</strong>0µ 385v<br />
Finlux VR3724 Int no rew or FFwd Cam slide ass'y Pt no 8681 4927<br />
Fisher FVHP530 Display goes off when operate pressed Dry joint Q009 on LH side of case of vert heat sink<br />
Fisher FVHP615 No stop/eject when heated BA6304 chip temp sensitive<br />
Fisher FVHP7<strong>10</strong> No Rewind Rew button S585 gone hi res<br />
Fisher FVHP905 Cass In light perm lit dry joints cass housing plug<br />
Fisher FVHP906 Dead - no 5v or 12v from psu chip STK5461<br />
Fisher FVHP907 Accepts tape but no mechs signal diode D504 on the input of the key decode A/D convertor BA6334 IC502 leaky<br />
Funai 5843 Head speed too fast Replace C2, 3 & 4 on head drum<br />
replace worn master cam,not allowing brake lever to latch on Golstar 374-005A,<br />
Goldstar D17 mechs No Ffwd/Rew <strong>aft</strong>er initial speed start<br />
Konig 1<strong>10</strong>08<br />
Goldstar GHV1240I E-E tuning varying in & out Check C715 in IF unit or brown glue under coil connected to tuner units TU pin<br />
Goldstar GHV1240I Won't accept tapes Arm ass'y on RH side of housing had lost its spring due to broken lug - pt no 435-148R<br />
Goldstar GHV1244I Goes straight into Rew when sw on Timing (line up hole in main cam, sliding lever & chassis in stop)<br />
Goldstar GHV1246I Goes into rew for 5 secs then off with "< >" flashing in display Loading motor dead spot<br />
Goldstar GHV1246I Wont accept tape spring post broken on side of cass housing<br />
Goldstar GHV1290I Beeps for no apparent reason Dry joints on beeper<br />
Goldstar GHV1290I Horrible patterning & hum bar on play and record . C118 <strong>10</strong>0uF 16v ( 47uF fitted in machine ) C122 47uF 63v<br />
Goldstar GHV1290I hum bar on e-e & patt on pback & rec Check caps C118, 112, <strong>10</strong>8, <strong>10</strong>7, 155, 120, 122 all 47µ, C121 & 123 <strong>10</strong>0µ<br />
Goldstar GHV1290I Hum Bars on pic C712 in IF module<br />
5v at syscon & digitron chip goes low to 3 - 4v.(OK at PSU o/p) - high res print between<br />
Goldstar GHV1290I Int slow Ffwd/Rew & display dims & goes out<br />
pin 11 P5<strong>10</strong>1 (reg 6v0) & C502 - caused by glue<br />
Goldstar GHV1290I Load arms don't move<br />
Goes out of time with graunching noises every few times Play<br />
Inner sect broken allowing gear rack to free-wheel<br />
Goldstar GHV1296I is selected Replace Load/Mode Ass'y £8.15 23128 from CHS - split pulley on motor
Change language