p17eus5n7g1vqn15ad31m19bp1p894.pdf

NETWORK INFRASTRUCTURE XXX SOLUTIONS
KGC-352
PoE Powered 1000Base-T to 1000Base-X Gigabit Media Converters
PowEr ovEr EthErnEt nEtworkinG solutions
The Gigabit media converter is designed to convert 1000Base-T signals to/from 1000Base-X fiber
signals. It is used to extend the connection distance between two Gigabit Ethernet devices via
fiber cable transparently with no performance degradation. With the SFP (Mini-GBIC) connector
design, the media converter not only supports existing variety of multimode and single mode
fibers, but also preserves the flexibility to adapt to any change of your fiber network in the future.
It also supports center chassis installation with optional power redundancy and management
features when a larger fiber network is required. With pre-configured fiber transceivers, the
converter also can support Bi-Di WDM and CWDM fiber network applications.
• Full wire speed performance • SFP flexibility • Best Conversion Latency
• Lower power consumption • Optional DIN-Rail Mounting • Powered by PoE, AC Adapter, USB
• Options for Bi-Di Communication • Options for CWDM
KGC-352
JENNE PART #:: DESCRIPTION
KGC-352-SX LC, MMF, 500 M
KGC-352-LX LC, MMF, 550 M; SMF, 10 KM
KGC-352-LX20 LC, SMF, Up to 20 KM
KGC-352-LX30 LC, SMF, Up to 30 KM
KGC-352-LX50 LC, SMF, Up to 50 KM
KGC-352-LX70 LC, SMF, Up to 70 KM
KGC-352-W3510 Bi-Di LC, SMF, Up to 10 KM
KGC-352-W5310 Bi-Di LC, SMF, Up to 10 KM
KGC-352-W3520 Bi-Di LC, SMF, Up to 20 KM
KGC-352-W5320 Bi-Di LC, SMF, Up to 20 KM
KGC-352-W3540 Bi-Di LC, SMF, Up to 40 KM
KGC-352-W5340 Bi-Di LC, SMF, Up to 40 KM
KGC-352-W3410 Bi-Di SC, SMF, Up to 10 KM
KGC-352-W4310 Bi-Di SC, SMF, Up to 10 KM
KGC-352-W3410S Bi-Di SC, SMF, Up to 10 KM
KGC-352-W4310S Bi-Di SC, SMF, Up to 10 KM
KC-3DR Optional Din-Rail bracket
KS-1080 PoE PSE switch
KPOE-100 PoE PSE mid-span injector
misCEllanEous nEtworkinG ProduCts
KCD-303P-A/ KCD-303P-B
PoE Powered 1000Base-T to 1000Base-X Gigabit Media Converters
The industrial rated KCD-303P series supports three switched connections including copper
and fiber for networks over POF (Plastic Optical Fiber). The copper ports support 10/100Mbps
auto-negotiation and auto-MDI/MDIX for Cat.5 plug-and-play. The fiber ports support plug-less
connections of high bandwidth 100Mbps data rate over POF cables. POF technology offers a
complementary solution to UTP copper wire for industrial, office and home networks because
it is low cost, weight little, thin, easy and safe to install and electronic noise immunity.
• Supports 3 switching-base network segments – 2 x Copper, 1 x Fiber
• Auto MDI/MDI-X crossover function on the UTP copper port
• Supports IEEE 802.3x flow control for full-duplex operation
• Supports Back-pressure flow control for half-duplex operation
• Wide operating temperature range for temperature critical environment
• Support wall mounting and panel mounting
• Industrial-rated Emission and Immunity performance
KCD-303P-A
KCD-303P-B
JENNE PART #:: DESCRIPTION
KCD-303P-A1 2 UTP Ports, 1 POF Ports, 1.5 mm POF Cable
KCD-303P-A2 2 UTP Ports, 1 POF Ports, 2.2 mm POF Cable
KCD-303P-B1 1 UTP Ports, 2 POF Ports, 1.5 mm POF Cable
KCD-303P-B2 1 UTP Ports, 2 POF Ports, 2.2 mm POF Cable
������������������������������������������������������������������������������������������������
��������������������������������������������������������������������������������������������
������������������������������������������������������������������������������������������������
140
www.jenne.com • 800-422-6191
KGC-352
KCD-303P-A