eWON Family

More documents

Recommendations

Info

3.3.4.2.2.2 Outgoing Global parameters General Reference Guide eWON Configuration Figure 34: Modem Outgoing Global setup page Control Description Dial and connection timeout Enable compression Delay between dialout retries Idle time before hanging up Max outgoing call duration Hang up if no outgoing action after Time allowed for the whole establishment of the PPP link to be up. This means modem call, modem negotiation, PPP negotiation and logon. This time includes all trials on each server. This is thus a global time. Enable the compression negotiation request when an outgoing call occurs. This includes all compression modes known by the eWON PPP engine (Van Jacobson, header compression,…). In case of an unsuccessful attempt to establish the outgoing communication, then eWON will retry to establish it again. This parameter will allow you to define the amount of time the eWON will wait to try and establish again the outgoing action. eWON will hang up after this amount of time if no data transfer occurs on the PPP link between the eWON (any type of PPP packet) and a remote host (Computer). Select between Check incoming or Check outgoing to select the monitored traffic. Note: this is the same parameter as for incoming connection. The maximum amount of time of the outgoing call. When this amount of time is reached, then the eWON stops the PPP communication. When a PPP link is triggered by an outgoing action (not by DialOnDemand), you can force the interruption of the line immediately after the actions (set 0) or let the PPP active for an amount of time (set >0). The PPP link will be shut down after the x minutes even if transfers are in progress. The Idle time before hanging up is always active. Table 35: outgoing calls configuration controls RG-001-0-EN ver 1.10 eWON® - 09/09/2010 - ©eWON sa Page 41
Select next server in case of error Reset modem after Minimum GPRS connection duration Reset GPRS modem after Allocated Budget Reset budget period Current period budget Current VOL IN/OUT info Reset Click on the Update button when you have filled this part of the eWON configuration. General Reference Guide eWON Configuration When the call to a server failed, you can choose the behavior of the next call. eWON will be configured to: • Use last valid server • Always return to server 1 • Use only server 1 • Use only server 2 Consider this parameter like a Watchdog parameter. To avoid eWON to stay stucked due to any modem reason, you can use this parameter to force a reset of the modem after xxx outgoing calls failure. Only available on eWON with GPRS modem. Time in seconds: if the GPRS dial-out connection is shorter than this time, the connection is considered as ERROR. If set to "-1", this time is not tested (default value = 4). See "Note: GPRS modem connection error management" on page 42. Only available on eWON with GPRS modem. Maximum number of GPRS connection ERROR accepted before the modem is reset (default value = 5). See "Note: GPRS modem connection error management" on page 42. This is the allocated time budget for outgoing calls. When a communication initiated by the eWON is in progress, the current period budget (remaining time) is reduced. When all the time budget is used, the eWON cannot make outgoing call. This is the time allowed in order to use the budget. After the call period is over, a new period is started and the new period timer is reset to this value. In the above example, this means that the current budget period is reset to 24 hours each 168 hours. The reset period is restored to its value each time one of the three configuration fields is modified. This is the remaining call budget for the current period, expressed in hours:min:sec. A new budget can be provided; this restarts a new reset period. For example, in the above example 24 hours are remaining, if we force 100 hours as call budget, the reset period is reset. This means that for the newly started period, 100 hours are allocated. A new period will start again in a delay of 168 hours. Information: counters of volume transmitted (IN and OUT) You can reset it by checking the ’Reset’ box. Table 35: outgoing calls configuration controls Note: GPRS modem connection error management The "Minimum GPRS connection duration" and the "Reset GPRS modem after" parameters have been added to monitor problems with GSM- GPRS connection. In case these problems occur, the result can be a short or unsuccessful PPP connection. In that case the Dialout Out to server works (CONNECT message received from the modem), then the PPP negociation starts and then: 1. either the PPP connection starts 2. or the LCP negociation fails but in any case the connection is short (less than 2 to 4 seconds). In the first case above, a message is logged in the events.txt file saying: eppp-Open client connection eppp-Close client connection (Cnxtime: 0 S. [2]) In the second case, the PPP connection does not start, but a message is logged in the events.txt file saying eppp-PPP negociation failed. (user/password/pap-chap) The problem may be due to a bad configuration of APN,user,password, authentication mode (CHAP, PAP), but it can also be due to a GSM problem for doing an "Attach" to the GPRS. In that case, it may be required to reset the modem to help it recover. REM1: these test only apply to GPRS connection, if username or password is invalid for another type of dial-out, the modem will not be reset. REM2: eppp-PPP negociation failed. (user/password/pap-chap) The above message is generated for any type of dial-out that50 fails before PPP connection goes online. RG-001-0-EN ver 1.10 eWON® - 09/09/2010 - ©eWON sa Page 42
Page 1 and 2: eWON Family 500, 2001, 2001CD, 4001
Page 3 and 4: Table of content 5.4.3 Tag name con
Page 5 and 6: Table of content 8.3.7 $dtSS [Sched
Page 7 and 8: 2 The eWON login page 2.1 Access fr
Page 9 and 10: 3.2 Users Setup The Users Setup pag
Page 11 and 12: 3.2.5 User’s directory restrictio
Page 13 and 14: 3.3 System Setup General Reference
Page 15 and 16: 3.3.1.2 Alarms (globals parameters)
Page 17 and 18: 3.3.1.5 Task Planner Since Firmware
Page 19 and 20: 3.3.1.5.2 Edit Action page When you
Page 21 and 22: General Reference Guide eWON Config
Page 23 and 24: When using modem port for VCOM, the
Page 25 and 26: 3.3.2.7 SNMP Setup 3.3.2.7.1 Commun
Page 27 and 28: 3.3.3 Diagnosis 3.3.3.1 Overview Ge
Page 29 and 30: 3.3.3.4 Debug Control Description L
Page 31 and 32: 3.3.4.1.1 Modem setup page Warning:
Page 35 and 36: 3.3.4.1.1.4 PSTN: Leased line confi
Page 37 and 38: 3.3.4.1.2 Ethernet LAN & WAN From t
Page 39 and 40: Each mechanisms provides you all or
Page 41: General Reference Guide eWON Config
Page 45 and 46: 3.3.4.2.3 ADSL General Reference Gu
Page 49 and 50: VPN with a Server General Reference
Page 53 and 54: 3.3.4.2.6 Ethernet Gateway behavior
Page 55 and 56: Dial On Demand General Reference Gu
Page 57 and 58: 3.3.4.3.4 Callback Warning: dependi
Page 59 and 60: 3.3.4.3.5 Routing Warning: Dependin
Page 61 and 62: 3.3.4.3.5.1 Static routes General R
Page 63 and 64: All these parameters are in the com
Page 69 and 70: 3.3.4.5.2 Erase & Format Figure 60:
Page 71 and 72: 3.4 Tag Setup 3.4.1 Tag definition:
Page 77 and 78: Published value Modbus TCP visibili
Page 79 and 80: 3.4.2.2 Tag "Alarm Action" edit win
Page 81 and 82: 3.4.2.2.2.1 SMS_RECIPIENT: syntax T
Page 83 and 84: 3.4.2.2.3.1 File content: General R
Page 87 and 88: 3.8 Wizards To help you quickly and
Page 89 and 90: 5 The eWON IO Servers 5.1 Introduct
Page 91 and 92: 5.2.4 Standard IO server configurat
Page 93 and 94:
General Reference Guide IO Servers
Page 95 and 96:
5.3.3 Tag name convention IO Server
Page 97 and 98:
5.3.3.2 Slave Address This is the a
Page 99 and 100:
5.4.3.1 ValueName General Reference
Page 101 and 102:
Page 103 and 104:
• Status register: General Refere
Page 105 and 106:
eWON DF1 address 5.6.2.2 Topic conf
Page 107 and 108:
5.6.3 Tag name convention IO Server
Page 109 and 110:
• "e" indicates the element numbe
Page 111 and 112:
Serial FINS network Serial FINS nod
Page 113 and 114:
Supported memory areas: Modifier: G
Page 115 and 116:
5.8 S5-AS511 IO Server 5.8.1 Introd
Page 117 and 118:
NOTES: • For DB the smallest elem
Page 119 and 120:
5.9.2.1 Communication Setup General
Page 121 and 122:
5.9.3.1 ValueName ValueName follows
Page 123 and 124:
Example of use of SN_LO and SN_HI i
Page 125 and 126:
5.10.2.2.1 ENERGY TAGS The followin
Page 127 and 128:
5.10.2.3.2 PT100 input AI5 and AI6
Page 129 and 130:
5.11 MEM IO Server 5.11.1 Introduct
Page 131 and 132:
Baud Rate 5.12.2.2 Topic configurat
Page 133 and 134:
Examples • Bit access modifier: G
Page 135 and 136:
5.13 S7-200 (PPI - ISOTCP) 5.13.1 I
Page 137 and 138:
5.13.2.3 COM configuration (MPI por
Page 139 and 140:
5.13.3.1 Value Name The syntax is t
Page 141 and 142:
5.14 HITACHI IO Server 5.14.1 Intro
Page 143 and 144:
5.14.2.1 Value Name The syntax is t
Page 145 and 146:
Page 147 and 148:
5.15.2.2 Topic configuration Genera
Page 149 and 150:
Page 151 and 152:
5.16.3 Tag name convention General
Page 153 and 154:
6 eWON Monitoring Web Interface Gen
Page 155 and 156:
6.1.4 Real time graph If a real tim
Page 157 and 158:
6.3 Historical table General Refere
Page 159 and 160:
6.5 Historical Alarm screen General
Page 161 and 162:
6.7 Diagnostic General Reference Gu
Page 163 and 164:
6.7.2 Status General Reference Guid
Page 165 and 166:
6.7.2.3 VCom 6.7.2.4 Status General
Page 167 and 168:
6.7.4 Real Time Log General Referen
Page 169 and 170:
you can also activate the Serial De
Page 171 and 172:
7 Retrieving Data from eWON 7.1 Lis
Page 173 and 174:
7.3 FTP transfer FTP stands for the
Page 175 and 176:
8.2 Export fields syntax definition
Page 177 and 178:
8.2.4 $ut [Update Time] General Ref
Page 179 and 180:
$ft General Reference Guide Export
Page 181 and 182:
For fixed interval, $in parameter m
Page 183 and 184:
8.3.4 $dtAH [Alarm History] General
Page 185 and 186:
8.3.6 $dtEV [EVent file] 8.3.6.1 Ex
Page 187 and 188:
8.3.8 $dtSE [Script Expression] 8.3
Page 189 and 190:
General Reference Guide Export Bloc
Page 191 and 192:
General Reference Guide Export Bloc
Page 193 and 194:
8.3.11 $dtSV General Reference Guid
Page 195 and 196:
8.3.14 $dtSC General Reference Guid
Page 197 and 198:
8.3.16 $dtTR [TAR file] 8.3.16.1 Ex
Page 199 and 200:
9 Upgrading the eWON firmware 9.1 P
Page 201 and 202:
Click on the Finish Button when the
Page 203 and 204:
General Reference Guide Upgrading t
Page 205 and 206:
9.5 Upgrade Bootloader (to upgrade
Page 207 and 208:
10.2.2 Non-volatile configuration T
Page 209 and 210:
If an error is detected during the
Page 211 and 212:
10.7 Duplicate IP detection (User L
show all

eWON Family

Create successful ePaper yourself

Delete template?

Save as template?