UniModSet / MetcomTSet - baer-gmbh.com

More documents

Recommendations

Info

UniModSet / MetcomTSet 48 � Signal quality: Enter: AT+CSQ, Modem reply: value from 0 (bad) to 31 (very good). For data calls signal should be more then 19. � Select data rate for target device (e.g. counter): AT+IPR=2400 (if device operates at 2400 Baud). Modem reply: OK Possible data rates: 300, 1200, 2400, 4800, 9600, 19200 (Default), 28800, 38400 or 57600 Baud � Set parameters for terminal program to 2400, 8N1. � Set data format: AT+ICF=5,1 (if device uses format 7E1). Modem reply: OK Alternative: AT+ICF=3,3 (default value) if device uses 8N1 AT+ICF=2,1 if device uses 8E1 � Set parameters for terminal program to 2400, 7E1 Alternative: 2400, 8N1 2400, 8E1 � Select automatic answering: ATS0=1, Modem reply: OK. � Disable echo: Enter ATE0, Modem reply: OK. With this setting the modem does not echo characters sent by the target device. Some counters may not communicate correctly if they receive their own output. � Suppress modem result codes: Enter ATQ1. No answer from modem. This prevents the modem from sending result codes to the target device. The result codes can cause trouble with some counters. Alternative: ATQ0 V0 (Responses as numbers), Modem replay: 0 � Save current parameters: Enter AT&W. No answer (if ATQ1 command issued before) or answer=0 (if ATQ0 V0). � Parametering finished.
11 Protocol Test UniModSet / MetcomTSet With the program-expansion "Protocol Test" (optional) is it possibly to make connection to the counter and to enforce a simple counter test („Read Data“). 49
Page 1 and 2: UniModSet / MetcomTSet Parameteriza
Page 3 and 4: Table of Contents UniModSet / Metco
Page 5 and 6: 3 Installation For installation run
Page 7 and 8: Examples: 4.1 UniMod... with parame
Page 9 and 10: 5 Settings The global system settin
Page 11 and 12: 6 Configuration UniModSet / MetcomT
Page 13 and 14: UniModSet / MetcomTSet It is possib
Page 15 and 16: UniModSet / MetcomTSet It is also p
Page 17 and 18: UniModSet / MetcomTSet Optionally t
Page 19 and 20: 6.3 GSM-3 for UniMod GSM-3 / GSM-3H
Page 21 and 22: UniModSet / MetcomTSet Optionally i
Page 23 and 24: The following registers exist for G
Page 25 and 26: 6.4 GSM-4 for UniMod GSM-4 UniModSe
Page 27 and 28: UniModSet / MetcomTSet Optionally i
Page 29 and 30: UniModSet / MetcomTSet Since the fi
Page 31 and 32: UniModSet / MetcomTSet � Timeout:
Page 33 and 34: UniModSet / MetcomTSet Optionally t
Page 35 and 36: UniModSet / MetcomTSet Option: Sinc
Page 37 and 38: Optional it is possible to set the
Page 39 and 40: 6.7 Ethernet for UniMod Ethernet un
Page 41 and 42: 7 Change the configuration UniModSe
Page 43 and 44: Possible settings: UniModSet / Metc
Page 45 and 46: 10.1 Programming with the terminal
Page 47: UniModSet / MetcomTSet Request Answ

UniModSet / MetcomTSet - baer-gmbh.com

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?