Short manual ER23K - Blemo

More documents

Recommendations

Info

Factory Configuration Drive factory setting The <strong>ER23K</strong> is factory-set for the most common operating conditions: • Display: Drive ready (rdY) with motor stopped, and motor frequency with motor running, • Logic inputs LI5 and LI6, analog input AI3, analog output AOC and relay R2 are not assigned, • Stop mode in the event of detected fault: freewheel. Code Description Value Page bFr [Standard mot. freq] 50 Hz 26 tCC [2/3 wire control] 2-wire transition detection control 27 UFt [U/F mot 1 selected] SVC (Sensorless flux vector control for constant torque applications) 34 ACC< DEC [Acceleration] [Deceleration] 3.00 seconds 29 LSP [Low speed] 0 Hz 29 HSP [High speed] 50 Hz 29 ItH [Mot. therm. current] nominal motor current (value depending on drive rating) 29 SdC1 [Auto DC inj. level 1] 0.7 x nominal drive current, for 0.5 seconds 30 SFr [Switching freq.] 4 kHz 31 rrS [Reverse assign.] Logic input 2 (LI2) 37 PS2 [2 preset speeds] Logic input 3 (LI3) 30 PS4 [4 preset speeds] Logic input 4 (LI4) 30 Fr1 [Ref.1 channel] Analog input 1 (AI1) 26 SA2 [Summing ref. 2] Analog input 2 (AI2) (1) r1 [R1 Assignment] Detected fault(FLt): the contact opens in the event of a detected fault (or drive off) (1) brA [Dec ramp adapt.] Automatic adaptation of the deceleration ramp in the event of overvoltage on braking (1) Atr [Automatic restart] No automatic restarting after a detected fault (1) Stt [Type of stop] Normal stop mode on deceleration ramp (rMP) (1) (1) See programming <strong>manual</strong> for more details. Check that the above values are compatible with the application. In this case, the drive can be used without changing the settings. 22 02/2010
Factory Configuration (continued) ER23-...K Single phase supply ER23-/3K/4K/6K 3-phase supply (1) Line choke, if used (single phase or 3-phase) (2) Relay contacts for remote signalling of drive status U1 R / L1 R / L1 U / T1 (1) V1 S / L2 S / L2 V / T2 W1 M 3 a T / L3 R1A W / T3 (1) R1C (2) P0 R1B PA / + R2A 02/2010 23 PB R2C PC / - CLI Forward Reverse 2 preset speeds 4 preset speeds LI1 +10 LI2 AI1 Speed reference LI3 COM LI4 LI5 AI3 LI6 Summing reference AI2 24V AOV AOC COM
Page 1: COMPACT-LINE 02/2010 Short manual E
Page 4 and 5: Important Information NOTICE Read t
Page 6 and 7: WARNING LOSS OF CONTROL • The des
Page 8 and 9: Mounting Mounting and temperature c
Page 10 and 11: Wiring Power and circuit protection
Page 12 and 13: Logic input switch This switch assi
Page 14 and 15: Functions of the power terminals Te
Page 16 and 17: Control terminals Access to the con
Page 18 and 19: AOV AOC Analog output voltage AOV o
Page 20 and 21: Sizes 1 to 4 Size 5 to 7 Size 8 Siz
Page 24 and 25: Programming HMI description Functio
Page 26 and 27: Configuration of the bFr, Fr1 and t
Page 28 and 29: [SPEED REFERENCE] (rEF-) [SPEED REF
Page 30 and 31: Code Name/Description Adjustment ra
Page 32 and 33: [MOTOR CONTROL] (drC-) With the exc
Page 34 and 35: Code Name/Description Adjustment ra
Page 36 and 37: Code Name/Description Factory setti
Page 38 and 39: [MONITORING] (SUP-) Parameters can
Page 40 and 41: Migration ER22K - ER23K The ER23K i
Page 42 and 43: Fault detection codes which cannot
Page 44 and 45: Fault detection codes which can be
Page 46: BLEMO ® Frequenzumrichter Siemenss

Short manual ER23K - Blemo

Create successful ePaper yourself

Delete template?

Save as template?