Short manual ER23K - Blemo

More documents

Recommendations

Info

Programming HMI description Functions of the display and keys • Four 7-segment displays • REF LED, illuminated when rEF- menu is active • Charge LED • MON LED, illuminated when SUP- menu is active • CONF LED, illuminated when SEt, drC, I-O, CtL, FUn, FLt or COM menu is active • MODE button: When rEF- displayed, switches to SEt- menu. Otherwise, switches to rEF- menu. See page 28 • RUN button: Controls motor switch-on in forward mode if parameter tCC in the I- O- menu is set to LOC page 27 • 2 CANopen status LEDs • Exits a menu or parameter, or clears the displayed value to return to the previous stored value • Jog dial - Acts as a potentiometer in local mode. For navigation when turned clockwise + or counterclockwise - and selection / validation when pushed. It acts as reference potentiometer, if parameter Fr1 in the CtL- menu is set to AIU1 STOP/RESET button • Used to reset faults to zero • It can be used to control motor stopping - If tCC (I-O- menu) is not set to LOC, it is a freewheel stop. - If tCC (I-O- menu) is set to LOC, stopping is on a ramp, but if injection braking is in progress, a freewheel stop takes place. Normal display, with no detected faults, and the motor not running: • : Display of the parameter selected in the [MONITORING] (SUP-) menu (default selection: motor frequency). • In current limiting mode or saturation of speed or current loop, the display flashes. • InIt: Initialization sequence • rdY: Drive ready • dCb: DC injection braking in progress • nSt: Freewheel stop • FSt: Fast stop • tUn: Auto-tuning in progress 24 02/2010
Menus structure Refer to the programming <strong>manual</strong> for comprehensive menu description. Power-up Parameter selection These 3 parameters are only visible at first power up of the drive. Settings can be changed subsequently in menu: drC- for bFr CtL- for Fr1 I-O- for tCC. [SPEED REFERENCE] (rEF-) [SETTINGS] (SEt-) [MOTOR CONTROL] (drC-) [INPUTS / OUTPUTS CFG] (I-O-) [COMMAND] (CtL-) [APPLICATION FUNCT.] (FUn-) [FAULT MANAGEMENT] (FLt-) [COMMUNICATION] (COM-) [MONITORING] (SUP-) See programming <strong>manual</strong> 1 flash (save) A dash appears after menu codes to differentiate them from parameter codes. Example: [SETTINGS] (SEt-) menu, ACC parameter. 02/2010 25
Page 1: COMPACT-LINE 02/2010 Short manual E
Page 4 and 5: Important Information NOTICE Read t
Page 6 and 7: WARNING LOSS OF CONTROL • The des
Page 8 and 9: Mounting Mounting and temperature c
Page 10 and 11: Wiring Power and circuit protection
Page 12 and 13: Logic input switch This switch assi
Page 14 and 15: Functions of the power terminals Te
Page 16 and 17: Control terminals Access to the con
Page 18 and 19: AOV AOC Analog output voltage AOV o
Page 20 and 21: Sizes 1 to 4 Size 5 to 7 Size 8 Siz
Page 22 and 23: Factory Configuration Drive factory
Page 26 and 27: Configuration of the bFr, Fr1 and t
Page 28 and 29: [SPEED REFERENCE] (rEF-) [SPEED REF
Page 30 and 31: Code Name/Description Adjustment ra
Page 32 and 33: [MOTOR CONTROL] (drC-) With the exc
Page 34 and 35: Code Name/Description Adjustment ra
Page 36 and 37: Code Name/Description Factory setti
Page 38 and 39: [MONITORING] (SUP-) Parameters can
Page 40 and 41: Migration ER22K - ER23K The ER23K i
Page 42 and 43: Fault detection codes which cannot
Page 44 and 45: Fault detection codes which can be
Page 46: BLEMO ® Frequenzumrichter Siemenss

Short manual ER23K - Blemo

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?