The Multi Interface Controller (M.I.C.) is an on-line ... - VVV System sro

More documents

Recommendations

Info

Stop bits RS-232 serial communication requires one or two stop bits at the end of the data. Select the option that matches the device requirements. 1 Stop bit RTS / CTS Output * 2 Stop Bits When th<strong>is</strong> option <strong>is</strong> enabled, RTS / CTS hardware protocol <strong>is</strong> activated. BASE STATION will output a request to send (RTS) signal when it <strong>is</strong> ready to send <strong>an</strong>y data <strong>an</strong>d will wait for CTS before sending it. NOTE: RTS/CTS <strong>is</strong> always active in the input port. * Not Active Active MS9530 Voyager RF Base Station - 31 - Printed: September 2002 Version: 1.1 Status: Approved
ACK / NAK Output When th<strong>is</strong> option <strong>is</strong> enabled, ACK / NAK software protocol <strong>is</strong> activated. NOTE: D<strong>is</strong>able XON/XOFF <strong>an</strong>d RTS/CTS when th<strong>is</strong> option <strong>is</strong> enabled * Not Active Active *BEL / CAN When th<strong>is</strong> option <strong>is</strong> enabled, the Base Station will emit a beep whenever a BEL( 07 Hex) character <strong>is</strong> received.If CAN (18 Hex)<strong>is</strong> received the sc<strong>an</strong>ner will exit comunications loop silently. ACK / NAK software protocol must be activated. Not active Active XON / XOFF Output When th<strong>is</strong> option <strong>is</strong> enabled, XON / XOFF software protocol <strong>is</strong> activated. NOTE: D<strong>is</strong>able RTS/CTS <strong>an</strong>d ACK/NAK when th<strong>is</strong> option <strong>is</strong> enabled * Not Active Active MS9530 Voyager RF Base Station - 32 - Printed: September 2002 Version: 1.1 Status: Approved
Page 1 and 2: MS9530 VOYAGER RF BASE STATION MANU
Page 3 and 4: BARCODE PARAMETERS.................
Page 5 and 6: Introduction The B
Page 7 and 8: General characteris</strong
Page 9 and 10: c) TTL Serial ASCII The</st
Page 11 and 12: Keyboard Wedge mode The</st
Page 13 and 14: Configuration MS9530 Voyager RF Bas
Page 15 and 16: DOWNLOADING RS232 CONFIGURATION MOD
Page 17 and 18: SYSTEM COMMAND Return to default Th
Page 19 and 20: Beeper activation Activate or deact
Page 21 and 22: Italian Norwegi<st
Page 23 and 24: F1 F3 F5 F7 User Defined F2 MS9530
Page 25 and 26: Alt Mode activation When th
Page 27 and 28: RS 232 OUTPUT When this</st
Page 29 and 30: BARCODE PARAMETERS Minimum Length T
Page 31: Data Bits RS-232 serial communicati
Page 35 and 36: DATA FORMAT BASE STATION is
Page 37 and 38: Preambles When this</strong
Page 39 and 40: Character Substitution: Adv
Page 41 and 42: ** CRTL MODIFIER ** CTRL+Sc
Page 43 and 44: Editing Functions Editing functions
Page 45 and 46: Delete Character Insert DELAY Char.
Page 47 and 48: EDIT ALL TYPES 00 CODE 39 41 TELEPE
Page 49 and 50: Insert character: This</str
Page 51 and 52: EML EML is a defin
Page 53 and 54: SHORT BEEP Packet Comman</s
Page 55 and 56: Any other will be considered as “
Page 57 and 58: APPENDIX B _____________Control Cod
Page 59 and 60: F1 F2 F3 F4 F5 MS9530 Voyager RF Ba
Page 61 and 62: F22 F23 F24 ALT SHIFT CTRL MS9530 V
Page 63 and 64: SHIFT+F1 SHIFT +F2 SHIFT+F3 SHIFT +
Page 65 and 66: APPENDIX C _____________ASCII Code
Page 67 and 68: A B C End selection RF MODE D E F M
Page 69 and 70: BASE STATION CONNECTION LIST June 1
Page 71 and 72: IBM PS2/40/50/55/60/80 01 Y-02 IBM
Page 73 and 74: SILICONGRAPHICS INDIGO 2 01 Y-02 SP
Page 75 and 76: SAMPLES SHEET EAN 13 UPCA EAN8 UPCE
Page 77 and 78: _______________Return to default___
Page 79 and 80: ___________End of message control c
Page 81 and 82: ____________________Data Bits______
Page 83 and 84:
______________Inter Character Delay
show all

The Multi Interface Controller (M.I.C.) is an on-line ... - VVV System sro

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?