The Multi Interface Controller (M.I.C.) is an on-line ... - VVV System sro

More documents

Recommendations

Info

RS232 End of Message Control Code Th<strong>is</strong> section will fix the End of Message control code character sent after data when RS232 output interface <strong>is</strong> selected. You c<strong>an</strong> add <strong>an</strong>y control character by reading "User defined" <strong>an</strong>d then a code of the "Control code table" in Appendix B. CR NONE ETX LF STX User Defined Use the following barcodes to send [CR] [LF] when [CR] <strong>is</strong> selected as end of message control code when required CR -> CR LF * CR -> CR MS9530 Voyager RF Base Station - 33 - Printed: September 2002 Version: 1.1 Status: Approved
DATA FORMAT BASE STATION <strong>is</strong> able to m<strong>an</strong>age the decoded data in m<strong>an</strong>y different ways using special features as Preambles,Postambles,.... <strong>The</strong> followed secuence <strong>is</strong>: 1º) Apply EDIT FUNCTIONS 2º) Apply CHARACTER SUBSTITUTION 3º) Add BARCODE/DEVICE IDENTIFIERS 4º) Add PREAMBLES 5º) Add POSTAMBLES 6º) Add END OF MESSAGE CONTROL CODES 7º) Add MOBIL ID Th<strong>is</strong> way the data will be like th<strong>is</strong>: {Mobil ID}{Preambles} {Identifiers}{ EDITED Data}{Postambles}{End of Message} <strong>The</strong> user should notice th<strong>is</strong> to get the desired data. MS9530 Voyager RF Base Station - 34 - Printed: September 2002 Version: 1.1 Status: Approved
Page 1 and 2: MS9530 VOYAGER RF BASE STATION MANU
Page 3 and 4: BARCODE PARAMETERS.................
Page 5 and 6: Introduction The B
Page 7 and 8: General characteris</strong
Page 9 and 10: c) TTL Serial ASCII The</st
Page 11 and 12: Keyboard Wedge mode The</st
Page 13 and 14: Configuration MS9530 Voyager RF Bas
Page 15 and 16: DOWNLOADING RS232 CONFIGURATION MOD
Page 17 and 18: SYSTEM COMMAND Return to default Th
Page 19 and 20: Beeper activation Activate or deact
Page 21 and 22: Italian Norwegi<st
Page 23 and 24: F1 F3 F5 F7 User Defined F2 MS9530
Page 25 and 26: Alt Mode activation When th
Page 27 and 28: RS 232 OUTPUT When this</st
Page 29 and 30: BARCODE PARAMETERS Minimum Length T
Page 31 and 32: Data Bits RS-232 serial communicati
Page 33: ACK / NAK Output When this<
Page 37 and 38: Preambles When this</strong
Page 39 and 40: Character Substitution: Adv
Page 41 and 42: ** CRTL MODIFIER ** CTRL+Sc
Page 43 and 44: Editing Functions Editing functions
Page 45 and 46: Delete Character Insert DELAY Char.
Page 47 and 48: EDIT ALL TYPES 00 CODE 39 41 TELEPE
Page 49 and 50: Insert character: This</str
Page 51 and 52: EML EML is a defin
Page 53 and 54: SHORT BEEP Packet Comman</s
Page 55 and 56: Any other will be considered as “
Page 57 and 58: APPENDIX B _____________Control Cod
Page 59 and 60: F1 F2 F3 F4 F5 MS9530 Voyager RF Ba
Page 61 and 62: F22 F23 F24 ALT SHIFT CTRL MS9530 V
Page 63 and 64: SHIFT+F1 SHIFT +F2 SHIFT+F3 SHIFT +
Page 65 and 66: APPENDIX C _____________ASCII Code
Page 67 and 68: A B C End selection RF MODE D E F M
Page 69 and 70: BASE STATION CONNECTION LIST June 1
Page 71 and 72: IBM PS2/40/50/55/60/80 01 Y-02 IBM
Page 73 and 74: SILICONGRAPHICS INDIGO 2 01 Y-02 SP
Page 75 and 76: SAMPLES SHEET EAN 13 UPCA EAN8 UPCE
Page 77 and 78: _______________Return to default___
Page 79 and 80: ___________End of message control c
Page 81 and 82: ____________________Data Bits______
Page 83 and 84: ______________Inter Character Delay

The Multi Interface Controller (M.I.C.) is an on-line ... - VVV System sro

Create successful ePaper yourself

Delete template?

Save as template?