CCD-BARCODE SCANNER Programming Manual - Dr. Vogt GmbH

More documents

Recommendations

Info

2.2 Loop of <strong>Programming</strong> The philosophy of programming parameters has been shown on the flow chart of 2.1. Basically user should 1. Scan Start of Configuration. 2. Scan all necessary labels for parameters that meet applications. 3. Scan End of Configuration to end the programming. 4. To permanently save the settings you programmed, just scan label for Save Parameters. 5. To go back to the Default Settings, just scan label for Set All Defaults. 2.3 Factory Default Settings The factory default settings are shown with < > and bold in the following sections. You can make your own settings by following the procedures in this manual. If you want to save the settings permanently, you should scan the label of "Save Parameters" in chapter 2.4, otherwise the settings will not be saved after the decoder power is off, and all settings will go back to previous settings. By scanning "Set All Default" label, the settings will go back to the factory default settings. 9
2.4 Main Page of Configuration Save Parameters Recall Stored Parameters Set All Defaults Start Configuration End Configuration Abort Configuration Version Information 10 %$ + / 0 %$ + / 1 %$ + / 2 %$ + / 3 %$ + / 4 %$ + / 6 %$ + / 5 Save Parameters - The parameter settings will be saved permanently. Recall Stored Parameters - Replace the current parameters by the parameters you saved last time. Set All Defaults - Set all the parameters to the factory default settings. Abort Configuration - Terminate current programming status. Version Information - Display the decoder version information and date code.
Page 1 and 2: CCD-BARCODE SCANNER Programming Man
Page 3: 5.12 BC412 Code Parameters ........
Page 6 and 7: Power supply for RS-232C scanner- T
Page 8 and 9: 2. RS-232 Output DB 9 Female Pin No
Page 12 and 13: Chapter 3 Interface and Reading Mod
Page 14 and 15: Ch.4 Communication Parameters 4.1 R
Page 16 and 17: 4.2 Keyboard Wedge Mode Parameters
Page 18 and 19: 4.3 Output Characters Parameters A>
Page 20 and 21: 4.4 Wand Emulation Mode Parameters
Page 22 and 23: Ch.5 Bar Codes & Others 5.1 Symbolo
Page 24 and 25: BC412 ON %0 OO8 Code 2 of 6 ON %0 P
Page 26 and 27: C> Check Digit Transmission UPC-A C
Page 28 and 29: D> Decode Asterisk Enable E> Set Up
Page 30 and 31: %4 F 1 + Fix Length (2 Sets Availab
Page 32 and 33: D> Set Up Code Length To set the fi
Page 34 and 35: %4 H1 + Fix Length (2 Sets Availabl
Page 36 and 37: %4 I 1 + Fix Length (2 Sets Availab
Page 38 and 39: C> Set Up Code Length To set the fi
Page 40 and 41: %4 K 1 + Fix Length (2 Sets Availab
Page 42 and 43: %4L1+ Fix Length (2 Sets Available)
Page 44 and 45: %4 N1 + Fix Length (2 Sets Availabl
Page 46 and 47: %4 O1 + Fix Length (2 Sets Availabl
Page 48 and 49: %4 P1 + Fix Length (2 Sets Availabl
Page 50 and 51: %4 T 1 + Fix Length (2 Sets Availab
Page 52 and 53: Belgium Denmark Turkey %0 Z V A %0
Page 54 and 55: UPC-A EAN-13/JAN-13 CODE 39 CODABAR
Page 56 and 57: 6.3 Reading Level Bar Equals High 6
Page 58 and 59: 6.9 Setup Deletion To setup the del
Page 60 and 61:
BC412 Telepen Resvered5 All Codes N
Page 62 and 63:
B> Symbologies Selection UPC-A EAN-
Page 64 and 65:
6.11 Setup IR Sensor %0 XH0 63 Ena
Page 66 and 67:
Appendix B ASCII Table NULL SOH 00
Page 68 and 69:
B 40 41 E H K N Q T W Z ] 42 43 44
Page 70 and 71:
Appendix C Function Key Table F1 F2
show all

CCD-BARCODE SCANNER Programming Manual - Dr. Vogt GmbH

Create successful ePaper yourself

Delete template?

Save as template?