CCD-BARCODE SCANNER Programming Manual - Dr. Vogt GmbH

More documents

Recommendations

Info

BC412 Telepen Resvered5 All Codes None %8 1 O+ %81T+ %8 1 R+ %8 1 S + %814+ 59 Code 2 of 6 %8 1 P + Resvered4 %8 1 Q+ C> Character Position to be Deleted 1. Decimal Value (Appendix A) 2. Complete %820+ D> Number of Characters to be Deleted 1. Decimal Value (Appendix A) 2. Complete %830+
6.10 Setup Insertion To setup the insertion of output characters: 1. Scan the label of the desired set. 2. Scan the label of the desired symbology. 3. Go to the Decimal Value Tables in Appendix A, scan label(s) that represents the desired position to be inserted. 4. Scan the "Complete" label of "Character Position to be Inserted". 5. Go to the ASCII Tables in Appendix B or Function Key Tables in Appendix C, scan label(s) that represents the desired characters to be inserted. 6. Scan the "Complete" label of "Characters to be Inserted". Repeat the steps 1 - 6 to set additional insertion. A> Select Insertion Set Number 1. 1st Set 3. 3rd Set 5. 5th Set %500+ %502+ %504+ 60 2. 2nd Set 4. 4th Set 6. 6th Set %501+ %503+ %505+
Page 1 and 2:
CCD-BARCODE SCANNER Programming Man
Page 3:
5.12 BC412 Code Parameters ........
Page 6 and 7:
Power supply for RS-232C scanner- T
Page 8 and 9:
2. RS-232 Output DB 9 Female Pin No
Page 10 and 11: 2.2 Loop of Programming The philoso
Page 12 and 13: Chapter 3 Interface and Reading Mod
Page 14 and 15: Ch.4 Communication Parameters 4.1 R
Page 16 and 17: 4.2 Keyboard Wedge Mode Parameters
Page 18 and 19: 4.3 Output Characters Parameters A>
Page 20 and 21: 4.4 Wand Emulation Mode Parameters
Page 22 and 23: Ch.5 Bar Codes & Others 5.1 Symbolo
Page 24 and 25: BC412 ON %0 OO8 Code 2 of 6 ON %0 P
Page 26 and 27: C> Check Digit Transmission UPC-A C
Page 28 and 29: D> Decode Asterisk Enable E> Set Up
Page 30 and 31: %4 F 1 + Fix Length (2 Sets Availab
Page 32 and 33: D> Set Up Code Length To set the fi
Page 34 and 35: %4 H1 + Fix Length (2 Sets Availabl
Page 36 and 37: %4 I 1 + Fix Length (2 Sets Availab
Page 38 and 39: C> Set Up Code Length To set the fi
Page 40 and 41: %4 K 1 + Fix Length (2 Sets Availab
Page 42 and 43: %4L1+ Fix Length (2 Sets Available)
Page 44 and 45: %4 N1 + Fix Length (2 Sets Availabl
Page 46 and 47: %4 O1 + Fix Length (2 Sets Availabl
Page 48 and 49: %4 P1 + Fix Length (2 Sets Availabl
Page 50 and 51: %4 T 1 + Fix Length (2 Sets Availab
Page 52 and 53: Belgium Denmark Turkey %0 Z V A %0
Page 54 and 55: UPC-A EAN-13/JAN-13 CODE 39 CODABAR
Page 56 and 57: 6.3 Reading Level Bar Equals High 6
Page 58 and 59: 6.9 Setup Deletion To setup the del
Page 62 and 63: B> Symbologies Selection UPC-A EAN-
Page 64 and 65: 6.11 Setup IR Sensor %0 XH0 63 Ena
Page 66 and 67: Appendix B ASCII Table NULL SOH 00
Page 68 and 69: B 40 41 E H K N Q T W Z ] 42 43 44
Page 70 and 71: Appendix C Function Key Table F1 F2
show all

CCD-BARCODE SCANNER Programming Manual - Dr. Vogt GmbH

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?