Turret Lathes - Hardinge Inc.

More documents

Recommendations

Info

Pads © Hardinge Inc., 2003 All specifications are subject to change without notice. Overview Master Collets, Master Feed Fingers and Pads from Hardinge ® Hardinge has manufactured collets for over 110 years. Using those years of expertise, Hardinge designs master collets and master feed fingers that perform better than other products in the marketplace. The Style "S" Master Collet overcomes all the problems associated with master collets. When loading bars, the rugged shoulder of the pad locates against the front of the groove in the master collet. There are no set screws or clamps to be damaged or loosened. When a part is machined, the working forces are against the rear shoulder of the pad which is located against the rear shoulder of the groove in the master collet. Again, there are no screws or clamps to wear or break. The clamp which holds the pads captivated in the collet literally floats longitudinally, assuring that there is never any pressure on the clamp. There are no holes in the OD of the master collet, or on the ID of the pads, resulting in maximum bearing on the workpiece and the spindle collet seat. When Style "S" collets are used, there will never be high spots on the spindle collet seat caused by the master collet and pad design. When selecting master collets from this catalog, remember the Style "S" design has been in existence for over 50 years and is the preferred system. The Style "B" Master Feed Finger and Pads are uniquely designed and proven by over fifty years of use in the machine tool industry. The straight-forward design allows for full bearing of the pad ID on the workpiece. There are no screws or tabs to wear or to remove bearing area from the pads ID. The master feed fingers are spring tempered to the proper gripping tension for maximum longevity. Custom master feed fingers can be easily and quickly manufactured at Hardinge to give extremely light grip, or heavier grip for nonstandard applications. The use of Style "B" Master Feed Fingers will assure you of minimum downtime on your production floor. The "AF" Master Feed Finger and Pads are designed to give you extreme flexibility with a very small investment. Each set of pads has a range of 1 ⁄32" adjustment down, reducing the inventory of pads required. Each click on the adjusting collar adds or subtracts between 6 to 8 pounds of pressure on the bar stock. This master outshines all others when feeding thin wall tubing. If the stock you run is very abrasive, these pads can be adjusted to maintain the force required to feed your stock when competitive pads would have to be replaced. This master feed finger may not have the full range of your collet, but within its range it will prove to be a real boost to your productivity and it will reduce your overall operating cost. Why purchase master collets and feed fingers rather than solids? While the initial investment will be slightly more, the advantage of achieving more versatility at a lower net cost assures the user of a profitable return. Master collets and feed fingers are capable of holding and feeding bar stock in a variety of sizes and shapes by using interchangeable pads. Thus, the same workholding tool can be used for more than one job to reduce tooling cost, provide greater flexibility in operation, and save on storage space. Pads for master collets and feed fingers are available from stock in round, hexagon, and square shapes. Extruded and unique shapes can be custom-made through our Special Collet Department. Pads are available in a variety of materials, including hardened steel, cast iron, bronze, and nylon to meet specific workholding and work-feeding needs. Chapter 3 Page 119
Chapter 3 Page 120 WE MAKE SPECIALS Extruded, Angular Slotted, .0002" TIR, Special Shapes. If you need it, we can make it. Pads Pad Pad Seg- Round Hex Square Style Description Part Number ments Min. Max. Min. Max. Min. Max. S10 Smooth & Serrated 5601-00- 3 1 ⁄8" (3.17) 1" (25.40) 1 ⁄4" (6.35) 7 ⁄8" (22.22) 55 ⁄64" (21.83) 11 ⁄16" (17.46) Emergency Collet 5601-14-10-000000 S12 Smooth & Serrated 5603-00- 3 1 ⁄8" (3.17) 1 1 ⁄4" (31.75) 1 ⁄4" (6.35) 1 1 ⁄16" (26.98) 1 ⁄4" (6.35) 7 ⁄8" (22.23) Emergency Collet 5603-14-10-000000 Semi-Hard Emerg 5603-13-10-000000 S15 Smooth & Serrated 5605-00- 3 1 ⁄8" (3.17) 1 1 ⁄2" (38.10) 1 ⁄4" (6.35) 1 5 ⁄16" (33.33) 1 ⁄4" (6.35) 1 1 ⁄16" (26.98) Emergency Collet 5605-14-10-000000 Semi-Hard Emerg 5605-13-10-000000 S16 Smooth & Serrated 5607-00- 3 1 ⁄8" (3.17) 1 5 ⁄8" (41.28) 1 ⁄4" (6.35) 1 13 ⁄32" (35.72) 1 ⁄4" (6.35) 1 5 ⁄32" (29.36) Emergency Collet 5607-14-10-000000 Semi-Hard Emerg 5607-13-10-000000 S20 Smooth & Serrated 5609-00- 3 1 ⁄8" (3.17) 2" (50.80) 1 ⁄4" (6.35) 1 23 ⁄32" (43.66) 1 ⁄4" (6.35) 1 13 ⁄32" (35.72) Emergency Collet 5609-14-10-000000 Semi-Hard Emerg 5609-13-10-000000 S22 Smooth & Serrated 5611-00- 3 1 ⁄8" (3.17) 2 1 ⁄4" (57.15) 1 ⁄4" (6.35) 1 15 ⁄16" (49.21) 1 ⁄4" (6.35) 1 19 ⁄32" (40.48) Emergency Collet 5611-14-10-000000 Semi-Hard Emerg 5611-13-10-000000 S26 Smooth & Serrated 5613-00- 4 1 ⁄8" (3.17) 2 5 ⁄8" (66.68) 1 ⁄4" (6.35) 2 1 ⁄4" (57.15) 1 ⁄4" (6.35) 1 27 ⁄32" (46.83) Emergency Collet 5613-14-10-000000 Semi-Hard Emerg 5613-13-10-000000 S30 Smooth & Serrated 5615-00- 4 1 ⁄8" (3.17) 3" (76.20) 1 ⁄4" (6.35) 2 9 ⁄16" (60.32) 1 ⁄4" (6.35) 2 1 ⁄8" (53.97) Emergency Collet 5615-14-10-000000 Semi-Hard Emerg 5615-13-10-000000 S35 Smooth & Serrated 5617-00- 4 1 ⁄8" (3.17) 3 1 ⁄2" (88.90) 1 ⁄4" (6.35) 3" (76.20) 1 ⁄4" (6.35) 2 7 ⁄16" (61.91) Emergency Collet 5617-14-10-000000 Semi-Hard Emerg 5617-13-10-000000 S40 Smooth & Serrated 5619-00- 4 1 ⁄8" (3.17) 4" (101.60) 1 ⁄4" (6.35) 3 7 ⁄16" (87.31) 1 ⁄4" (6.35) 2 13 ⁄16" (71.43) S50 Smooth & Serrated 5623-00- 4 1 ⁄8" (3.17) 5" (127.00) 1 ⁄4" (6.35) 4 5 ⁄16" (109.53) 1 ⁄4" (6.35) 3 1 ⁄2" (88.90) Hardinge Inc. One Hardinge Drive, PO Box 1507 Elmira, New York 14902-1507 USA Internet: www.hardingetooling.com & www.hardingeworkholding.com Pad Capacity WRENCHES FOR STYLE "S" CLAMPS Style "S" Wrenches Size Pads Part Number — Bristol Socket Handle For Both Size Sockets 7909-00-00-000000 — Socket Wrench .111" S10, S12, S15, S16, S20, S26 7909-00-00-000001 L Wrench: B Spline .111" S10, S12, S15, S16, S20, S26 7637-00-00-000000 — Socket Wrench .145" S22*, S30, S35, S40, S50 7909-00-00-000002 L Wrench: C Spline .145" S22*, S30, S35, S40, S50 7639-00-00-000000 *For Warner & Swasey 21 ⁄4" and Miyano 11 ⁄4" capacity, order the .111" wrench CLAMPS FOR STYLE "S" MASTER COLLETS – Used to Hold Pads in Collet Spline Pad Number Part Number B Spline - .111" S10, S12, S15, S16, S20, S26 7619 C Spline - .145" S22*, S30, S35, S40, S50 7627 Style "S" Master Collet Pads HARDINGE The Style "S" design offers you: Maximum bearing surface between the spindle and head angle. Because there are no holes or slots in the head angle of the collet, uneven wear of the spindle will not result from continuous use. There are no threaded holes in the collet to be stripped or damaged. Ease of Use. Since the pads are interchangeable without removing the master collet from the spindle, collets do not have to be removed from the machine when changing the bar stock size. Independent clamps slide freely in and out of the master collet so they can be removed with ease. Secure Pad Installation. The unique dovetail anchor system securely holds pads in place while feeding bar stock. This design places the bar thrust on the shoulder of the pad. There is no pressure on the clamp assembly because it is ideally positioned between the pad shoulder and the recess of the collet. The pads cannot dislodge under normal use. ® STYLE "S" MASTER COLLET PADS NOTE: Millimeters in parentheses Bristol Socket Wrenches Bristol Wrench End View FAST SERVICE USA: 800-843-8801, Canada: 800-468-5946 Phone – USA & Other Countries: 607-734-2281 USA Fax: 607-734-3886, Int'l Fax: 607-734-1701
Page 1 and 2: Hardinge ® Collets For Single & Mu
Page 3 and 4: Page II SOLID- SINCE 1890 Humble be
Page 5 and 6: Page IV WORKHOLDING/INDUSTRIAL PROD
Page 7 and 8: 1 2 3 Page VI Orders may be placed
Page 9 and 10: Page VIII
Page 11 and 12: Chapter 2 Page 100 Turret Lathes Ta
Page 13 and 14: BARDONS & OLIVER Chapter 2 Page 102
Page 15 and 16: FOSTER Chapter 2 Page 104 Machine M
Page 17 and 18: GISHOLT Chapter 2 Page 106 Machine
Page 19 and 20: JONES & LAMSON Chapter 2 Page 108 M
Page 21 and 22: OSTER Chapter 2 Page 110 Machine Mo
Page 23 and 24: SIMMONS RIVIT Chapter 2 Page 112 Ma
Page 25 and 26: WARNER & SWASEY Chapter 2 Page 114
Page 27 and 28: Chapter 2 Page 116 WE MAKE SPECIALS
Page 29: Chapter 3 Page 118 Pads Table of Co
Page 33 and 34: Chapter 3 Page 122 Pads HARDINGE ®
Page 35 and 36: Chapter 3 Page 124 STYLE "CB" MASTE
Page 39 and 40: Chapter 3 Page 128 Pads STYLE "M" M
Page 45 and 46: Chapter 4 Page 134 TABLE OF CONTENT
Page 47 and 48: Chapter 4 Page 136 Accessories Hard
Page 49 and 50: Chapter 4 Page 138 1 A WE MAKE SPEC
Page 51 and 52: Chapter 4 Page 140 Accessories SCRE
Page 53 and 54: Chapter 5 Page 142 Special Workhold
Page 55 and 56: Chapter 5 Page 144 Extended Nose -

Turret Lathes - Hardinge Inc.

Create successful ePaper yourself

Delete template?

Save as template?