Fractional E1 Access Units

4-17
G.SHDSL Modem
Features
ATM Bridge & Router Modem
SHDTU03b
2/4-wire G.SHDSL.bis Bridge/Router
SHDTU03b, G.SHDSL bis Router Family are G.SHDSL .bis (Symmetrical High Speed
Digital Subscriber Loop) 2-wire/4-wire routers which comply with G.991.2 (2004)
standards and with optional feature of a built-in four port 10Base-T /100Base-TX
auto-negotiation and auto-MDIX switch. The SHDTU03b family provides business-class,
multi-range 192Kbps to 5.7Mbps (2-wire) or 384Kbps to 11.4Mbps (4-wire) payload
rates over existing single or two pairs copper wire. SHDTU03b, G.SHDSL.bis router, is
designed not only to optimize the service bit rate from central office to customer
premises but also integrates high-end Bridging/ Routing capabilities with advanced
functions such as Multi-DMZ, virtual server mapping and VPN pass-through.
Standard G.SHDSL ITU-T G.991.2 (2004)
Use existing copper loop infrastructures
Can operate in back to back configurations
SHDSL Line performance monitoring
Local management interface via console port
Intuitive Web based configuration
Complies with UL 1950, FCC part 15 Class B, EN60950
Raw and time stamped statistics
Bandwidth guarantee transmission equipment
SHDTU03bF-ET10R SHDTU03bF-ET10RS SHDTU03bAF-ET10RS
WAN 2-Wire 2-Wire 4-Wire
LAN 1 4 4
Auto-MDIX None Yes Yes
Port-based VLAN None Yes Yes
802.1q VLAN 1LAN / 8WAN 4LAN / 8WAN 4LAN / 8WAN
IP Precedence Yes Yes Yes
Maximum Data Rate 5.7Mbps 5.7Mbps 11.4Mbps
Mininum Data Rate 192Kbps 192Kbps 384Kbps
Ordering Information
SHDTU03bF-ET10R Stand-alone 2-wire G.SDHSL.bis router with firewall
protection and single Ethernet port
SHDTU03bF-ET10RS Stand-alone 2-wire G.SDHSL.bis router with firewall
protection and 4-port switching HUB
SHDTU03bAF-ET10RS Stand-alone 4-wire G.SDHSL.bis router with firewall
protection and 4-port switching HUB
The G.SHDSL.bis router allows customers to leverage the latest in broadband
technologies to meet their growing data communication needs. In bridge mode, the four
ports 10Base-T /100Base-T auto-negotiation and auto-MDIX switching ports may be
configured for IEEE802.1Q VLAN or port based VLAN applications.
Specifications
General Specifications
Supports
Coding
Data Rate
Impedance
LED Indicators
Dimensions (WxHxD)
Power
Power Consumption
Tempature
Hunidity
Memory
Ethernet
WAN interface connetor
LAN interface connector
Console port
.bis
General: Power, G.SHDSL: Link/Active,
Ethernet: 1, 2, 3, 4, Alarm
9 Watts
0~45oC for operating ; 0~70o ITU-T 991.2 (2004), Annex A, B, F & G
TC-PAM 16, TC/PAM-32
Up to 5.696Mbps, N*64Kbps
(N=3 to 89, default value=89) with one pair ;
Up to 11.392Mbps, N*64Kbps
(N=3 to 89, default value=89) with two pairs
135 ohm
18.7 x 3.3 x 14.5 cm
9VDC (vis power adapter)
C for storage
0~95% (non-condensing)
2MB flash memory, 8MB SDRAM
4-port switching hub (for ET10RS model),
support 10/100Base-T/TX, auto-negotiation,
auto-MDIX
RJ-45
RJ-45*4 (for ET10RS model)
RS-232 (DB9F)
Data Rate - 1 Pair Data Rate - 2 Pair Range (Mile/Km)
192Kbps 384Kbps 4.35/7.0
384Kbps 768Kbps 3.73/6.0
512Kbps 1.024Mbps 3.54/5.7
768Kbps 1.537Mbps 3.25/5.25
1.024Mbps 2.048Mbps 2.93/4.8
1.536Mbps 3.072Mbps 2.7/4.35
2.304Mbps 4.608Mbps 2.44/4.0
3.072Mbps 6.144Mbps 2.17/3.5
3.52Mbps 7.04Mbps 2.05/3.3
4.096Mbps 8.192Mbps 1.86/3.0
4.608Mbps 9.216Mbps 1.68/2.7
5.056Mbps 10.112Mbps 1.62/2.6
5.696Mbps 11.392Mbps 1.3/2.1
*Above distance based on 26AWG twisted-pair wiring