Fractional E1 Access Units
Fractional E1 Access Units
Fractional E1 Access Units
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
3-5<br />
<strong>E1</strong> DSU/CSU<br />
<strong>E1</strong> NTU Series<br />
ETU01U<br />
Single-Port, unframed <strong>E1</strong> <strong>Access</strong> Unit<br />
The ETU01U is a single port access unit for Unframed El service. Two models, one<br />
supporting AC (90-250V) and one supporting DC (-18 ~ -72V), are available. The<br />
ETU01U data channel supports a fixed transmission rate of 2.048Mbps. The built-in LTU<br />
with a line attenuation of up to 43 dB on twisted pair or coax cable, provides an<br />
approximate operating range up to 2km (using 22AWG). The ETU01U packs the data<br />
channel into the El link transparently. The ETU01U has many types of user-replaceable<br />
data channel modules, which directly support the following interfaces: V.35, X.21,<br />
RS-530, 10/100BASE-T Ethernet Bridge, and 10/100BASE-T Ethernet Router. RS-449 is<br />
Features<br />
Available with many types of user-replaceable data channel<br />
modules<br />
Multiple clock source selection<br />
Fixed 2.048Mbps rate<br />
Support local loopback and remote digital loopback.<br />
Ordering Info<br />
ETU01U Unframed <strong>E1</strong><br />
ETU01U/AC<br />
ETU01U/DC<br />
Application<br />
AC type<br />
DC type<br />
Optional Interface Modules<br />
ETU/TTU-V35 V.35 interface module<br />
ETU/TTU-X21 X.21 interface module<br />
ETU/TTU-530 RS-530 interface module<br />
ETU/TTU-449 RS-530 interface module plus RS-449 cable<br />
adapter<br />
ETU/TTU-G64K-CO G.703/64K Co-directional I/F<br />
ETU/TTU-NRZ NRZ/BNC interface module<br />
ETU/TTU-ET100 10/100Base-T Ethernet Bridge<br />
ETU/TTU-ET100R 10/100Base-T Ethernet Router<br />
supported by RS-530 module and a DB25 to DB37 adapter cable. The ETU01U fully<br />
meets all of the El specifications including ITU-T G.703 and G.823. The ETU01U<br />
features V.54 diagnostic capabilities for performing local loopback and remote digital<br />
loopback. The operator at either end of the line may test both the ETU01U and the line<br />
in the digital loopback mode. The loopback is controlled by either a manual switch or<br />
by the DTE interface for V.35 and RS-530. A front panel switch generates an internal<br />
511 bit pseudo random test pattern, according to ITU-T, for direct end-to-end integrity<br />
testing. The Err indicator flashes for each bit error detected.<br />
Specifications<br />
Clock modes<br />
Clock mode 0<br />
(DC<strong>E1</strong>)<br />
Clock mode 1<br />
(DCE2)<br />
Clock mode 2<br />
(DT<strong>E1</strong>)<br />
Clock mode 3<br />
(DTE2)<br />
Clock mode 4<br />
(DTE3)<br />
Receive and transmit clock<br />
(recovered) to the<br />
synchronous DTE<br />
Receive and transmit clock<br />
(internal oscillator) to the<br />
synchronous DTE<br />
Receive clock to the<br />
synchronous,and transmit<br />
clock from the synchronous<br />
device<br />
Receive and transmit clock<br />
from the Synchronous DCE<br />
(from ETC andERC pin)<br />
Receive and transmit clock<br />
from theSynchronous DCE<br />
Data rate<br />
(all from ETC pin)<br />
2048Kbps (clear channel)<br />
Power<br />
AC 90 — 250 VAC<br />
DC -18 — -75 VDC<br />
Environment Temperature 0 — 50°C (Operating);<br />
0 — 70°C (Storage)<br />
Humidity 0 — 90% non condensing<br />
Power Consumption 10W<br />
LEDs<br />
TD, RD, RTS, DCD, signal loss, alarm<br />
Dimensions(WxDxH) 195mm x 255mm x 45mm<br />
Weight<br />
1.5kg<br />
Test Switch/ Digital local loopback<br />
Diagnostics Digital remote loopback<br />
Analog local loopback<br />
Test pattern<br />
Compliance CE, FCC part 15 class A, ITU-T G.703,<br />
G.706 and G.732.
Change language