ITW DEVCON ENGINEERED COATINGS - ITW Futura Coatings

More documents

Recommendations

Info

9.1.3. Areas of bare metal shall receive a coat of <strong>Futura</strong>-Bond 610HS in accordance with Section 6.0. 9.1.4. Brush or spray apply Irabond UU 96 to primed and abraded areas only, at a wet film thickness of 2-3 Mils Allow a fifty (50) minute drying time and a maximum drying time of five (5) hours at 75°F. 9.1.5. Brush or spray apply Irathane 155 over the properly prepared areas to the recommended dry film thickness. 9.1.6. Do not apply Irathane 155 to surfaces that have not been properly prepared or primed. 9.2. The repair of small surface areas, such as those damaged during coating operations, shall be accomplished with power tools to remove all damaged coating(s), provide a surface roughness, and return exposed metal to a bright and roughened condition. 9.3. Adjacent, sound areas of coating shall be feathered, tapered, or roughened by hand or power tools for a minimum overlap distance of two (2) inches in all directions. 9.4. Prepared surfaces shall be re-coated in accordance with Section 5.0 and other applicable Sections. 9.4.1. Irathane 155 repairs are permitted using less than the standard unit quantities provided that the Irathane 155 is mixed at a 1:1 by volume ratio of the component “A” to component “B”. 10.0 INSPECTION 10.1. All work and materials supplied under this specification guideline shall be subject to competent and timely inspection by the contractor or his authorized representative. 10.2. The contractor shall, throughout the course of the coating work described in this specification guideline, impose a program of inspection and quality surveillance to ensure that the coating system is installed in a manner that complies with the requirements of this specification guideline and the Project/Job Specification. 10.3. Mandatory inspections shall be conducted to determine compliance with the "hold points" detailed in the Project/Job Specification, and "signed off" in the areas provided. 10.4. Inspections shall be conducted, a minimum of four (4) times per shift, or more frequently when coating work operations or changing environmental conditions require particular surveillance. 10.5. Cured coating shall be tested for holidays (pin holes) using a high-voltage DC holiday detector or equivalent instrument adjusted and operated in accordance with ASTM D5162-91(B), Discontinuity (Holiday) Testing of Non-conductive Protective Coating on Metallic Substrates. Irathane 155 can be tested at a rate of 100 volts/mil. All holidays should be repaired in accordance with Section 9.0 of this specification guideline. 10.6. Timely and daily completion of inspection documents by the inspector(s), contractor, or his designate, is highly recommended throughout the course of the job. These documents should record the following inspections: Surface preparation, surface temperature, dew point of substrate, temperature and humidity of ventilating air, batch numbers and identification of mixed coating components, wet film thickness or application rate of individual coats, dry film thickness of individual coats, recoat intervals, Location and repair of pinholes and determination of degree of cure. Page 8 of 9 04/10 Irathane 155 Steel
10.7. All coating inspection instruments, inspection standards, calibration standards, and testing materials shall be in good working order, appropriate for the use intended, and where required, shall have been calibrated within twelve (12) months of their use. The owner shall have access to all required calibration certificates. 10.8. Coating dry film thickness shall be determined by the use of magnetic thickness instruments used and calibrated in accordance with SSPC, Paint Application Standard PA2. 10.9. Coating areas that fail to meet the minimum dry film thickness requirements of the SSPC-PA2 survey method shall be repaired in accordance with the guidelines presented in Section 9.0. Page 9 of 9 04/10 Irathane 155 Steel
Page 1 and 2: 1.0 GENERAL. SPECIFICATION AND APPL
Page 3 and 4: 4.3. Prior to abrasive blast cleani
Page 5 and 6: 6.8. Futura-Bond 610HS shall be app
Page 7: 8.5.2. The second and/or subsequent

ITW DEVCON ENGINEERED COATINGS - ITW Futura Coatings

Create successful ePaper yourself

Delete template?

Save as template?