Backyard Circus Club

More documents

Recommendations

Info

Step 13 N13 N31 N15 N17 Swing Assembly *NOTE: Half-Bucket Swing (N17) is intended for use by children ages 3 to 5, under adult supervision. 1. Open C-Links (N30) and Pear Links (N31). *NOTE: When closing C-Links and Pear Links, securely tighten using a crescent wrench. 2. Attach two Long Chains (N13) to each Swing Seat (N15) and Half-Bucket Swing (N17) using Pear Links (N31) and C-Links (N30) (as shown in Inset A). 3. Attach two Short Chains (N12) to Trapeze Bar (N18) using C-Links (N30) (as shown in Inset A). 4. Attach Trapeze Rings (N14) to Trapeze Bar (N18) by connecting C-Links (N30) to both the Trapeze Bar (N18) and Trapeze Rings (N14) (as shown in Inset B). *NOTE: When completed, swing assemblies should look as shown in Inset B. 5. Securely close all C-Links (N30) and Pear Links (N31) by tightening with a crescent wrench. N13 N30 INSET A INSET B 32 N12 N30 N30 N14 N18
Step 14 H56 H4 N29 N10 H11 H3 H17 H28 H139 77 H3 N170 H135 N29 N26 H3 H24 H11 H28 H3 H116 A-Frame Assembly & Swing Hanger Installation *NOTE: It is possible to modify your 3 Position Swing Beam to a 2 Position Swing Beam for use in small yards. See Step 31, page 51 for instructions on how to modify the 3 Position Swing Beam to a 2 Position Swing Beam. Proceed with the following steps after making the modifications. 1. Attach Swing Hangers (N26) to Swing Beam (346) using 3/8" Hardware (H3) (H11) (H24) (H28) (H135) and 3/8" Bolt Cup (N29). *SUGGESTION: Use a locking pliers to hold on to Hex Head Bolts (H135). 2. Position Plaque (N83) in the approximate position shown and attach to Swing Beam using #10 Hardware (H157) or (H158) (as shown). 3. Attach Swing Beam Plate (N10) to Swing Beam (346) using 3/8" Bolt Cup (N29), 3/8" Hardware (H3) (H11) (H17) (H28) (H56), and 1/2" Hardware (H4) (as shown). *NOTE: Do not fully tighten hardware at this time. 4. Attach Upper A-Frame Block (81) and Lower A-Frame Block (82) (as shown) using 3/8" Hardware (H3) (H116). 5. Attach A-Frame Legs (77) to A-Frame Block assembly using 45 Bracket (N170) and 3/8" Hardware (H139) (H3) (H11) (H17). *NOTE: Do not tighten hardware completely at this time. 6. Lay assembly on the ground with A-Frame Legs (77) pointing in opposite directions. N83 H158 H157 81 33 82 H3 H11 346 H17 77
Page 1 and 2: Backyard Circus Club Assembly Instr
Page 3 and 4: Thoroughly read all Safety Instruct
Page 5 and 6: TABLE 3.1 Fall Height in Feet From
Page 7 and 8: COMMONLY ASKED QUESTIONS Question:
Page 9 and 10: 57 58 353 427 646 418 640 226 664 4
Page 11 and 12: 247 2@ 1 x 4 x 17" Fan Vertical (3-
Page 13 and 14: N20 N8 1@ Ship's Wheel (5-41-0021)
Page 15 and 16: N24 55 54 57 56 662 661 660 58 418
Page 17 and 18: H7 H1 H30 H32 H34 H28 H17 H24 HARDW
Page 19 and 20: H100 HARDWARE FOR ASSEMBLY *NOTE: T
Page 21 and 22: 418 418 Step 1 INSET A 638 DETAIL B
Page 23 and 24: Step 3 N8 H164 646 INSET A H163 H7
Page 25 and 26: Step 5 664 638 DETAIL A 664 H108 H1
Page 27 and 28: Step 7 *NOTE: Install Rail Uprights
Page 29 and 30: Step 8 H32 N21 222 H7 H170 H34 Rock
Page 31 and 32: Step 10 *NOTE: To ease assembly, as
Page 33: Step 12 715 408 Slide Installation
Page 37 and 38: Step 15 Continued from previous pag
Page 39 and 40: Step 17 648 INSET A H108 638 H1 647
Page 41 and 42: Step 19 H131 H11 638 639 H30 H3 651
Page 43 and 44: Step 21 1. Position Roof Frame Side
Page 45 and 46: Step 23 404 H194 401 412 404 A INSE
Page 47 and 48: Step 25 358 364 365 366 367 368 369
Page 49 and 50: Step 27 H154 H152 379 H194 INSET A
Page 51 and 52: Step 29 662 661 57 660 58 H154 53 H
Page 53 and 54: Step 31 1 1/2" 1 1/2" 2 Position Sw
Page 55: Limited Seven-Year and One-Year War

Backyard Circus Club

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?