I[_i]ADVERTENCJA - Ppe-pressure-washer-parts.com
I[_i]ADVERTENCJA - Ppe-pressure-washer-parts.com
I[_i]ADVERTENCJA - Ppe-pressure-washer-parts.com
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
g.<br />
i<br />
Move throttle lever to "Fast"<br />
as<br />
,\<br />
a rabbit.<br />
. Y<br />
10. Move choke lever to "Choke" position.<br />
position, shown here<br />
NOTE: For a warm engine, be sure the choke lever is<br />
in the "Run" position.<br />
11. When starting engine, position yourself as<br />
re<strong>com</strong>mended, grasp handle and pull recoil starter<br />
lightly until you feel some resistance, then pull<br />
briskly.<br />
/<br />
/<br />
f<br />
f<br />
14. if engine fires, but does not continue to run,<br />
squeeze trigger on spray gun to relieve internal<br />
pump <strong>pressure</strong>. Move choke lever to "Run"<br />
position, and repeat steps 11 through 13.<br />
15. if engine fails to start after six pulls, move choke<br />
lever to "Run" position, and repeat steps<br />
11 through 13.<br />
WARNING<br />
DO NOT touch hot surfaces and avoid hot exhaust gases.<br />
Allow equipment to coo! before touching.<br />
Keep at least 5 ft. (152 cm) clearance on all sides of<br />
<strong>pressure</strong> <strong>washer</strong> including overhead.<br />
Code of Federal Regulation (CFR) Title 36 Parks,<br />
Forests, and Public Property require equipment powered<br />
by an internal <strong>com</strong>bustion engine to have a spark<br />
arrester, maintained in effective working order, <strong>com</strong>plying<br />
to USDA Forest service standard 5100-1C or later<br />
revision. In the State of California a spark arrester is<br />
required under section 4442 of the California Public<br />
resources code. Other states may have similar laws.<br />
NOTE: Always keep the throttle lever in the "Fast"<br />
position when operating the <strong>pressure</strong> <strong>washer</strong>.<br />
/<br />
How to Stop Your C_eaning System<br />
1. Let engine idle for two minutes.<br />
2. Move throttle lever on engine to "Stop" position.<br />
12. Return recoil starter slowly. DO NOT let rope<br />
"snap back" against starter.<br />
WARNING<br />
DO position. NOT stop engine by moving choke lever to "Choke"<br />
3. ALWAYS point gun in a safe direction and<br />
squeeze spray gun trigger to release retained high<br />
water <strong>pressure</strong>.<br />
WARNING<br />
ALWAYS point gun<br />
in safe direction and squeeze spray<br />
gun trigger, to release <strong>pressure</strong> and avoid kickback each<br />
time, before starting engine.<br />
When starting engine, pull cord slowly until resistance is<br />
felt and then pull rapidly to avoid kickback.<br />
After each starting attempt, where engine fails to run,<br />
always point gun in safe direction and squeeze spray<br />
gun trigger to release high <strong>pressure</strong>.<br />
13. When engine starts, slowly move choke lever to<br />
"Run" position, as engine warms. If engine falters,<br />
move choke lever to "Choke" position, then to<br />
"Run" position.<br />
Keep high <strong>pressure</strong> hose connected to pump and spray<br />
gun while system is pressurized.<br />
ALWAYS point gun in safe direction and squeeze spray<br />
gun trigger, to release high <strong>pressure</strong>, every time you stop<br />
engine. Engage trigger lock when not in use.<br />
4. Engage trigger lock on spray gun when not in use.<br />
11