I[_i]ADVERTENCJA - Ppe-pressure-washer-parts.com
I[_i]ADVERTENCJA - Ppe-pressure-washer-parts.com
I[_i]ADVERTENCJA - Ppe-pressure-washer-parts.com
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
Problem<br />
Cause<br />
Correction<br />
Pump has following<br />
problems: failure to produce<br />
<strong>pressure</strong>, errat{c <strong>pressure</strong>,<br />
chattering, loss of <strong>pressure</strong>,<br />
low water volume.<br />
Detergent fails to mix with<br />
spray.<br />
1. Low <strong>pressure</strong> nozzle installed.<br />
2. Water inlet is blocked.<br />
3. inadequate water supply.<br />
4. inlet hose is kinked or leaking.<br />
5. Clogged inlet hose strainer.<br />
6. Water supply is over 100°F.<br />
7. High <strong>pressure</strong> hose is blocked<br />
or leaks.<br />
8. Gun leaks.<br />
9. Nozzle is obstructed.<br />
1.<br />
Chemical shut:off valves are in 1.<br />
the "Off" position.<br />
2. in:line filter is dirty.<br />
3. High <strong>pressure</strong> nozzle installed.<br />
1. Replace nozzle with high <strong>pressure</strong><br />
nozzle.<br />
2. Clear inlet.<br />
3. Provide adequate water flow.<br />
4. Straighten inlet hose, patch leak.<br />
5. Check and clean inlet hose strainer.<br />
6. Provide cooler water supply.<br />
7. Clear blocks in high <strong>pressure</strong> hose<br />
or replace hose.<br />
8. Replace gun.<br />
9. Clean nozzle.<br />
10. Pump is faulty. 10. Contact Sears service facility.<br />
Rotate chemical shut:off valve on<br />
desired chemical reservoir to "On"<br />
position.<br />
2. See "Check In:Line Filter".<br />
3. Replace nozzle with low <strong>pressure</strong><br />
nozzle.<br />
Engine runs good at noqoad<br />
but "bogs" when load is<br />
added.<br />
Engine speed is too slow.<br />
Move throttle control to FAST position.<br />
engine still "bogs down", contact Sears<br />
service facility.<br />
If<br />
1. Dirty air cleaner.<br />
2. Out of gasoline.<br />
1. Clean or replace air cleaner.<br />
2. Fill fuel tank.<br />
3. Stale gasoline.<br />
3. Drain gas tank; fill with fresh fuel.<br />
EngBne wHI not start; or<br />
starts and runs rough.<br />
4. Spark plug wire not connected<br />
to spark plug.<br />
5. Bad spark plug.<br />
4. Connect wire to spark plug.<br />
5. Replace spark plug.<br />
6. Water in gasoline.<br />
6. Drain gas tank; fill with fresh fuel.<br />
7. Overchoking.<br />
7. Open choke fully and crank engine.<br />
8. Excessively rich fuel mixture.<br />
8. Contact Sears service facility.<br />
EngBne shuts down during<br />
operation.<br />
Out of gasoline.<br />
Fill fuel tank.<br />
EngBne lacks power.<br />
Dirty air filter.<br />
Replace air filter.<br />
Engine "hunts" or falters.<br />
Choke is opened too soon.<br />
Move choke to halfway position<br />
engine runs smoothly.<br />
until<br />
23