I[_i]ADVERTENCJA - Ppe-pressure-washer-parts.com
I[_i]ADVERTENCJA - Ppe-pressure-washer-parts.com
I[_i]ADVERTENCJA - Ppe-pressure-washer-parts.com
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Yourcleaningsystemrequire someassemblyandis<br />
readyforuseonlyafterit hasbeenproperlyserviced<br />
withthere<strong>com</strong>mended oil andfuel.<br />
If you haveanyproblemswith theassemblyof<br />
your <strong>pressure</strong><strong>washer</strong>,pleasecallthe <strong>pressure</strong><br />
<strong>washer</strong>helplineat 1-800-222-3136.<br />
REMOVE PRESSURE WASHER<br />
FROM CARTON<br />
1. Slice two corners at the end of carton from top to<br />
bottom so the panel can be folded down flat.<br />
2. Remove hose reel box, fillers, and <strong>parts</strong> bag<br />
shipped with cleaning system.<br />
3. Remove spray gun, nozzle extension, and engine<br />
oil from fillers.<br />
4. Roll cleaning system out open end of carton.<br />
5. Check carton for additional loose <strong>parts</strong>.<br />
CARTON<br />
CONTENTS<br />
Check all contents. If any <strong>parts</strong> are mtssing or<br />
damaged, ca[[ the <strong>pressure</strong> <strong>washer</strong> helpline at<br />
1-800-222-3136.<br />
Main Unit<br />
Handle with Chemical<br />
Accessory tray<br />
Hose Reel Components<br />
High Pressure<br />
Hose<br />
Reservoir Assembly<br />
Spray Gun<br />
Nozzle Extension with Quick Connect<br />
Tip Holder<br />
• Oil Bottle<br />
• Parts Bag (which includes the following):<br />
• Owner's Manual<br />
• Owner's Registration Card<br />
Fitting and<br />
• Bag containing 4 multi-colored ProjectPro TM<br />
nozzles<br />
• Fresh Start Fuel Cartridge<br />
• Handle Fastening Hardware Kit (which includes):<br />
• Carriage Bolts (2)<br />
• Plastic Knobs (2)<br />
• Tree Clips (4)<br />
Be<strong>com</strong>e familiar with each piece before assembling<br />
the <strong>pressure</strong> <strong>washer</strong>. Identify all contents with the<br />
illustration on page 6. If any <strong>parts</strong> are missing or<br />
damaged, call the <strong>pressure</strong> <strong>washer</strong> helpline at<br />
1-800-222-3136.<br />
ASSEMBLING CLEANtNG SYSTEM<br />
Your Craftsman cleaning system ,,viii need assembly<br />
before operation:<br />
1. Attach handle to main unit.<br />
2. Connect chemical hose to pump.<br />
3. Attach hose reel to handle as shown on page 6<br />
according to instruction sheet included with hose reel.<br />
4. Add oil to engine crankcase.<br />
5. Add fuel to fuel tank.<br />
6. Connect high <strong>pressure</strong> hose to spray gun and pump.<br />
7. Connect water supply to pump.<br />
8. Attach nozzle extension to spray gun.<br />
9. Select/attach quick connect nozzle to nozzle<br />
extension.<br />
Attach<br />
Handme<br />
1. Place handle assembly onto handle supports<br />
connected to main unit. Make sure holes in handle<br />
align with holes on handle supports.<br />
/ I<br />
Handle '<br />
Hoes F_ r-__,,_<br />
Align i_ i<br />
Handle i i<br />
// Supports/i<br />
NOTE: It may be necessary to move the handle<br />
supports from side to side in order to align the handle<br />
so it will slide over the handle supports.<br />
2. Insert carriage bolts through holes from outside of<br />
unit and attach plastic knob from inside of unit.<br />
Tighten by hand.<br />
3. Place accessory tray over holes on handle<br />
(viewing from front of unit). Push tree clips into<br />
holes until they sit flat against accessory tray.<br />
: i<br />
.<br />
Insert multi-colored ProjectPro TM nozzles and<br />
other supplied accessories in spaces provided in<br />
accessory tray. See "How to Use Accessory Tray".<br />
J<br />
J