I[_i]ADVERTENCJA - Ppe-pressure-washer-parts.com
I[_i]ADVERTENCJA - Ppe-pressure-washer-parts.com
I[_i]ADVERTENCJA - Ppe-pressure-washer-parts.com
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
LONG TERM STORAGE<br />
if you do not plan to use the <strong>pressure</strong> <strong>washer</strong> for more<br />
than 30 days, you must prepare the engine and pump<br />
for long term storage.<br />
it is important to prevent gum deposits from forming in<br />
essential fuel system <strong>parts</strong> such as the carburetor, fuel<br />
filter, fuel hose or tank during storage. Also,<br />
experience indicates that alcohol-blended fuels (called<br />
gasohol, ethanol or methanol) can attract moisture,<br />
which leads to separation and formation of acids<br />
during storage. Acidic gas can damage the fuel<br />
system of an engine while in storage.<br />
Protect Fuel System<br />
Fuel Additive:<br />
if adding a fuel additive, fill the fuel tank with fresh<br />
fuel. If only partially filled, air in the tank will promote<br />
fuel deterioration during storage. Engine and fue[ can<br />
be stored up to 24 months with additive.<br />
• Add fuel additive following manufacturer's<br />
instructions.<br />
• Make sure you have water supply to pump inlet<br />
connected and turned ON.<br />
• Run the engine outdoors for several minutes to be<br />
sure that treated fuel has replaced the untreated<br />
fuel in the carburetor.<br />
If fuel additive is not used, remove all fuel from tank<br />
and run engine until it stops from lack of fuel.<br />
Change<br />
Oil<br />
While engine is still warm, drain oil from crankcase.<br />
Refill with re<strong>com</strong>mended grade. See "Changing Oil" on<br />
page 19.<br />
Oil Cylinder Bore<br />
• Remove spark plug. Squirt about 1/2 ounce of<br />
dean engine oil into the cylinder. Cover spark plug<br />
hole with rag. Pull recoil handle slowly to distribute<br />
oil. Avoid spray from spark plug hole.<br />
• Instal[ spark plug. DO NOT connect spark plug<br />
wire.<br />
Protect Pump<br />
To protect the pump use Sears pump saver to prevent<br />
freeze damage and lubricate pistons and seals.<br />
NOTE: Sears pump saver, item number 71-74403, is<br />
available as an optional accessory. [t is not included with<br />
the <strong>pressure</strong> <strong>washer</strong>.<br />
CAUTION<br />
* Failure to do so will permanently damage your pump<br />
and render your unit inoperable,<br />
* Freeze damage is not covered under warranty.<br />
To use the pump saver:<br />
,_<br />
CAUTION<br />
Always wear eye protection when using PumpSaver.<br />
1. Attach hose on pump saver can to pump inlet.<br />
2. Push in can top to dispense pump saver.<br />
3. When pump saver fluid begins to exit pump outlet,<br />
the pump is protected.<br />
4. Remove pump saver from pump inlet.<br />
OTHER<br />
• DO NOT store fuel from one season to another.<br />
• If possible, store your unit indoors and cover it to<br />
give protection from dust and dirt. BE SURE TO<br />
EMPTY THE FUEL TANK.<br />
WARN[NG<br />
DO NOT place a storage cover over a hot <strong>pressure</strong><br />
<strong>washer</strong>,<br />
Let equipment cool for a sufficient time before placing<br />
the cover on the equipment.<br />
22