1 - FIBERPOOL

More documents

Recommendations

Info

<strong>FIBERPOOL</strong> INTERNACIONAL TECHNICAL SERVICE: Ponent, 2-4-6 P.I. Sant Pere Molanta, 08799 Olèrdola BARCELONA An authorized technician should install the control panel. The main power line must be protected by a differential and a magnetothermic. The control panel will be fixed to the wall by a screw in the upper part (as if it were an eyebolt), and two more screws through the holes situated in the inside of the connection box. The control box will be placed above the electric pump. IP 54 TEMPERATURE: from 5º to 70ºC Voltage acceptable: +- 10% Feed cables and cables connecting the electric pump are to be of a 1,5mm2 wires with an insulation material of 1000v. Connections to the terminals must be made with pre-insulated connectors. The electric pump must be earthed. All site work to wire up the control panel should be done by an authorized technician, otherwise the manufacturer guarantee will not hold. WARNING: If the manufacturer uses the equipment for any purpose other than that specified, the equipment guarantees will not hold. Every 6 months, check for tightness all the connections. The installation must comply with norms of II category. The supply cables to the equipment must be installed in a way so that safety is maintained and the insulation is no subject to any damage. An anchoring device such as a packing gland must be used in order to prevent twisting and traction in the cable. FUNCTIONING MAIN DIAGRAM A - MAIN SWITCH I = start light on) 0 = stop (light off) A’ – SWITCH Man = Manual Aut = Automatic B - ADJUSTMENT In order to adjust the power consumption, we will follow the two frontal leds (green and yellow) using the potentiometer located at the left hand of the connection reglet. Turn the potentiometer in a clockwise direction to reduce the amperage. C - BREAKDOWN The red led indicates that there is a breakdown in the system. If this ever happens, please read the paragraph "Breakdown detection". D - RE-SET When a breakdown has occurred push this switch to restart the system. Very important: Do not use it until you have read the paragraph titled "Breakdown detection". E - TIME CLOCK F – LEDS SHOWING THE UNDERWATER LIGHT STATE. G - GENERAL SWITCH for connection or disconnection of the under water lights. POTENTIOMETER. Necessary element to adjust electric pump amperes (situated at the left hand of the connection reglet) Regulated current limitation control for pumps from 0,3 "A" up to a maximum of: 220vII……..3HP 220vIII…….4HP 380vIII…….5,5HP Flexibility of uses either for single phase or three phase pumps. System is disconnected when no current is detected. The circuit has the following functions: - Magnetic (short circuit). When working at high speed, facility of disconnection to avoid excess consumption. - RESET switch activates all the functions on the board. - The system complies with EC norms. G E A’ D F A B F C Ponent, 2-4-6 P.I. Sant Pere Molanta 08799 Olèrdola, BARCELONA E F F MOD: P.P.A.P. 220V II7380 v III 50/60HZ Corriente Corriente equipo: 0.3 A Potencia max.: 3hp (220V II) y 5.5hp(380V III) Nº de serie: FBP-00001 G A A’ C B D 4
<strong>FIBERPOOL</strong> INTERNACIONAL W V U L3 L2 L1 N W V U L3 L2 L1 N W V U L3 L2 L1 N alimentación alimentation feeding motor 220v. III potenciometro potentiomètre potentiometer alimentación alimentation feeding red /réseau supply system 220v. III alimentación alimentation feeding motor 380v. III potenciometro potentiomètre potentiometer alimentación alimentation feeding red /réseau supply system 380v. III alimentación alimentation feeding motor 220v. II potenciometro potentiomètre potentiometer alimentación alimentation feeding red /réseau supply system 220v. II L1 N Entrada 220v Ref: 20-IC-031 FOCO T 12v FOCO 12v Adjustment of the distance between the underwater light and the electric box: L1 N Ref: 20-IC-039 CON REM T FOCO 12v Characteristics of the transformer. - Complete isolation between coils and core. - Thermal relay included. Total protection against overloads and short circuits. - Primary regulation according to the distance between the underwater light and the transformer. - Isolation class B. Thread of copper H-180º - Automatic disconnection at 130 º. When it is cooled the transformer is connected automatically. Description of lighting system. It consist of: 1 General lighting switch. 1-2 Transformers 220/12v-300VA 1-2 frontal leds Procedure. Place general switch "G" in position "I". It will light up, as well as the leds on the panel. This means that the outlet connection 12v is correct. Entrada 220v 1 - Disconnect the electrical supply of the electric box. 2 - Take out the four screws on the frontal cover. 3 -Let the connections "faston" 1 and 2 and move the rest of connections of the electrical supply of the transformer to the meters( 10,25,40) An authorized technician must effect this operation. Do this operation without electrical tension. PROGRAMMING THE TIME CLOCK 1. Adjust time by turning the programme disk in the arrow direction. Hour time is indicated on the graduated dial. 2. Set the connection programme at 15 minutes intervals by locating the corresponding pins. 3. The red segment visible shows the period of the programmed connection. 3 1 2 5
Page 1 and 2: AÑO DE GARANTIA YEAR OF GUARANTEE
Page 3: FIBERPOOL INTERNACIONAL W V U L3 L2
Page 7 and 8: FIBERPOOL INTERNACIONAL W V U L3 L2

1 - FIBERPOOL

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?