DESCENDER DEVICES DESCENDER DEVICES - Kong
DESCENDER DEVICES DESCENDER DEVICES - Kong
DESCENDER DEVICES DESCENDER DEVICES - Kong
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
it from slipping a little at the start (fig 5).<br />
Use the lever to get the right speed for descent; pushing the<br />
lever over halfway the device will slow down descent until it becomes<br />
locked (fig. 6).<br />
It is best to make a safety loop to hold the same working position<br />
for a long time (fig. 7).<br />
Position for lowering materials or persons with brake (fig. 8).<br />
Important: secure the person being lowered with a second<br />
rope, where possible.<br />
10 - ORTIS<br />
Fig. 9 - Parts of ORTIS: A: Fixed side-plate (AL) - B: Mobile sideplate<br />
(AL) - C: Rope divider (AL) - D: Drum (AL) - E: Jamming<br />
cam (SS) - F: Pig-tail lever (SS) - G: Safety gate (SS) - H: Locking<br />
latch - I: Protruding pin (SS) - L: “Static rope lanyard” (article<br />
277) - (TX).<br />
AL: Aluminium - SS: Stainless steel - TX: Textile.<br />
Inserting the “Static rope lanyard”/rope:<br />
opening the device: turn the mobile side-plate anti-clockwise<br />
by 180°, lift the rope divider and keep the jamming cam open<br />
with your hand,<br />
insert the “Static rope lanyard” onto the drum, against the fixed<br />
side-plate and with the abseil loop opposite to the jamming cam<br />
(fig. 10),<br />
lower the rope-divider, inserting it into the groove of the drum<br />
(fig. 11)<br />
turn the “Static rope lanyard” for a second time around the<br />
drum (the loose one) clockwise (fig. 12),<br />
release the rope jamming cam, close the mobile side plate<br />
turning it 180° clockwise; check that the locking latch is in place<br />
against the protruding pin, insert the “Static rope lanyard” into the<br />
pig-tail lever in anticlockwise direction (fig. 13).<br />
Clip ORTIS into the anchor point and check that the safety<br />
gate is closed (fig. 14),<br />
How to use it:<br />
for abseiling: slowly lift up the “Static rope lanyard” inserted<br />
into the pig-tail lever with one hand (towards the operator), to<br />
free the jamming cam. Pay out slowly and evenly, using your<br />
hand as a brake (fig. 15),<br />
just let go of the rope to stop abseiling: this activates the jamming<br />
cam (fig. 16).<br />
Important: it is compulsory to use gloves to abseil in safety.<br />
11 - Pre and post use controls<br />
Make sure that the device:<br />
has not suffered from any mechanical deformations,<br />
does not show any signs of cracks or wear,<br />
does not have a worn “Static rope lanyard”/rope,<br />
is suited to the use you want to make of it,<br />
also check that:<br />
the pig-tail lever works freely on the jamming cam,<br />
the safety gate automatically closes when released.<br />
Height<br />
*Number of<br />
descents..<br />
Table A<br />
**Metres<br />
Parts to be replaced Serviceable parts<br />
for sliding…<br />
10 500 5,000<br />
N.5 ropes/lanyard ropes<br />
(for each 100 descents)<br />
Descender (for further<br />
5,500 m)<br />
Descensor (para otros 10.400<br />
100 1 100<br />
None<br />
metros)<br />
Cuerda (para otras 99 bajadas)<br />
105 100 10,500 N. 1 rope/lanyard rope<br />
N. 1 descender<br />
None<br />
10,500 1 10,500 N. 1 descender Rope (for further 99 descents)<br />
* Number of descents: (life of “Static rope lanyard”/rope 100 descents max).<br />
** Metres for paying out “Static rope lanyard”/rope in the descender: (life of descender<br />
10,550 m. paying out max).<br />
Master test: ITALIAN