passlock 1 - Ready Remote

More documents

Recommendations

Info

SATURN: Saturn vehicles up to the 2000 model year with factory keyless entry have a unique bypass. 1. Set all dip switches to the OFF (up) position. 2. Locate the Alarm Module behind the right rear quarter trim panel (trunk area). Connect the Pink and Yellow/Black wires of Connector J and D of the alarm module as shown. 3. Cut the Pink wire in half and connect as shown. Dip Switch #1 Off Dip Switch #7 Off Dip Switch #8 Off WHITE/GREEN TO WHITE/BLACK Status output from car starter (or to constant negative ground output when remote starter is activated).* *See page 16 if you do not have a Status wire © 2006 Directed Electronics N20402 08-06
TRANSPONDER / PASSKEY 3 / P.A.T.S.: ‘Smart Key’ & other Transponder systems Note: For this type of security system - you must sacrifice one of the spare keys that comes with the car. This key will be used for the transponder. The dealership can progam a spare key, but make sure they program all keys to the vehicle since learning just one transponder could erase all other key transponders (including the key used for the Bypass Module). 1. Set all dip switches on the bypass module to the OFF (up) position. 2. Remove the transponder from the key (there maybe a door on the top of the key that can be opened and the transponder can be removed). Or, the entire key may be mounted inside the Bypass Module. Be sure to cut the key in half or grind off some of the teeth to render it unusable. 3. Pull apart the case and place the transponder, or the head of the key, inside the 10 wire loop on the circuit board. Transponders are directional and must be placed along the same direction that the key would lay. Use the double stick foam tape provided -- one layer on the circuit board and then the transponder, or key, and finally the second double-stick foam tape layer on top of it to hold key securly in place. Make sure the white wires inside the module do not crisscross each other. Place Key with Transponder inside case on pc board as shown. Use double stick tape to hold to the key in place. N20402 08-06 4 © 2006 Directed Electronics
Page 1 and 2: 20402 & 29402 VATS / PASSLOCK / TRA
Page 3 and 4: List of vehicles and the types of s
Page 5 and 6: Honda S2000 2000-05 Transponder Hum
Page 7 and 8: Pontiac Grand Am 1999-2005 Passlock
Page 9 and 10: Use this chart with VATS, PASSLOCK
Page 11 and 12: PASSLOCK 1: 1. Put dip switches 1 a
Page 13: 8. When you have identified the cor
Page 17 and 18: For Car Starters that do not have a
Page 19 and 20: SAV / PASSLOCK / TRANSPONDEUR Modul
Page 21 and 22: Utilisez ce tableau pour les systè
Page 23 and 24: PASSLOCK 1: 1. Mettez les commutate
Page 25 and 26: 8. Une fois la bonne résistance id
Page 27 and 28: TRANSPONDEUR / PASSKEY 3 / P.A.T.S.
Page 29 and 30: Pour les démarreurs sans sortie de
Page 31 and 32: VATS / PASSLOCK / TRANSPONDER Modul
Page 33 and 34: Use esta tabla con VATS, PASSLOCK 1
Page 35 and 36: PASSLOCK 1: 1. Ponga el switch de m
Page 37 and 38: cual es menos que su valor deseado.
Page 39 and 40: TRANSPONDER / PASSKEY 3 / P.A.T.S.:
Page 41 and 42: Para Arrancadores de Motor que no t
Page 43: The company behind this system is D

passlock 1 - Ready Remote

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?