EUKC-09, 12, 18 AA - Johnson Controls

More documents

Recommendations

Info

Controls and Functions 1. Control panel 8 Description of components 1 Temperature ON/OFF 2 Ambient temperature 3 Save setting 4 Temperature set point 5 Day setting 6 Fan speed (Auto - High - Medium - Low) 2. Operation ON/OFF (Fig. 2): - Press "ON/OFF" button. The air conditioning unit will start and the operating LED will go on. - Press "ON/OFF" button once again. The air conditioning unit will stop operating and operating LED will go off. TIMER FAN SPEED FRESH SET OUT ENV COOL Fig. 2 - ON/OFF MODE FAN SLEEP TIME ON/OFF Fan control (Fig. 3): - Each time the FAN button is pressed, 1 2 3 4 5 6 7 8 9 TIMER ONOFF AUTO FAN SPEED DEFROST LOW MED Fig. 1 ERROR SAVE SET OUT ENV DAY DEBUG TEST AUTO FRESH COOL FAN 7 Defrost indicator 8 Renewal fresh air 9 Mode display 10 Error indicator 11 Programmer interval 12 Sleep mode indicator 13 Mode FAN SPEED SEG SLEEP DRY HEAT HIGH Fig. 3 - FAN 10 11 12 MODE FAN SLEEP TIME ON/OFF AUTO MODE FAN SLEEP TIME ON/OFF fan speed will change in the following sequence: - When in AUTO: In DEHUMIDIFICATION (DRY) mode, the fan operates at LOW speed. GB 13 14 15 16 17 18 14 Temperature setting 15 Fan 16 Sleep mode 17 Time setting 18 ON/OFF Temperature setting (Fig. 4): : Press this button to increase temperature. : Press this button to decrease temperature. (Press once to change 1° C.) - Temperature setting range is: HEAT 16° C to 30° C COOL 16° C to 30° C DRY 16° C to 30° C FAN Not selectable S E T MODE FAN SLEEP TIME ON/OFF Fig. 4 - TEMPERATURE
Note: Keyboard locking function. Pressing and simultaneously displays "EE" on the temperature set point display, and the keyboard is locked. To cancel this function, press and once again. SLEEP function (Fig. 5) In COOL and DRY modes, and after pressing the SLEEP button, the temperature set point will increase 1° C per hour. In the HEAT mode, the temperature set point will decrease 1° C per hour. The sleep function is not valid in FAN mode. SLEEP MODE FAN SLEEP TIME ON/OFF Fig. 5 - SLEEP FUNCTION Operating mode (Fig. 6) - Each time the MODE button is pressed, the operating mode will change in the following order: COOL DRY FAN HEAT AUTO - COOL is displayed in cooling mode. In this mode, a temperature lower than the room temperature should always be set. If not, only the fan mode will be operative. - DRY is displayed when the unit is operating in the dehumidification mode. In this operating mode the fan operate at low speed within the temperature range. Temperature control is not very precise in the dry mode, but energy saving is more than satisfactory. - HEAT is displayed in heating mode. In this mode, a temperature higher than the room temperature should always be set. Attention: In heat mode there is a cold air prevention effect when the unit is turned on. To avoid an uncomfortable atmosphere, the indoor fan is not operative until it detects that the indoor coil temperature is above the set temperature. - When the outdoor temperature is low and humidity is rather high, ice can form on the outdoor unit and diminish heating capacity. Should this occur, the controller will automatically activate the defrost cycle. During this cycle, the heat mode will be deactivated and DEFROST will be displayed. The unit will operate again automatically at the end of this cycle. - FAN is displayed in fan mode. During this period, room temperature cannot be adjusted and this room temperature is displayed. AUTO COOL FAN TIMER DRY HEAT Fig. 6 - MODE Fig. 7 MODE FAN SWING TIME ON/OFF Timing (Fig. 7) With the unit on or off, press the TIME button and then the and buttons to set the timer (Fig. 7), time setting (Fig. 8) or cancel the timer (Fig. 9). Once the corresponding option is selected, press TIME. GB MODE FAN SLEEP TIME ON/OFF TIMER TIMER TIMER ON DAY Fig. 8 Fig. 9 Fig. 10 ERROR SEG MODE FAN SLEEP TIME ON/OFF MODE FAN SLEEP TIME ON/OFF - Timer setting: Press MODE to set values desired: Week (1-7), time interval (1-4), timing (Timer ON or Timer OFF). - With the and buttons, adjust the element. Set by pressing TIME or cancel pressing TIME once again. The characters flash during adjustment. This setting can continue until it is deleted by pressing ON/OFF. Meanwhile, the timer setting is memorized (Figs. 10, 11). MODE FAN SLEEP TIME ON/OFF 9
Page 1: 12, 18 AA I SO 9 0 0 1 EUKC-09, E S
Page 4 and 5: Nota: Función de bloqueado del tec
Page 6 and 7: Códigos de error (fig.17): Si un p
Page 10 and 11: 10 TIMER OFF DAY SEG Fig. 11 Fig. 1
Page 12 and 13: 4. Operating modes Cooling In accor
Page 14 and 15: Remarque: fonction de blocage du cl
Page 16 and 17: Code d’erreur (fig.17) : Si un pr
Page 18 and 19: Controlos e funções 1. Painel de
Page 20 and 21: 20 TIMER OFF DAY SEG Fig. 11 Fig. 1
Page 22 and 23: 4. Modos de funcionamento Refrigera
Page 24 and 25: Bloccaggio della tastiera - Premend
Page 26 and 27: Codici di errore (Fig. 17) Se si pr
Page 28 and 29: Bedienelemente und Funktionen 1. Be
Page 30 and 31: TIMER OFF DAY Fig. 11 - Einstellung
Page 32 and 33: 4. Betriebsweisen Kühlen Der Mikro
Page 34 and 35: Nota: Functie toetsenbordblokkering
Page 36 and 37: Foutcode (fig.17): Als tijdens de w
Page 38 and 39: Betjeningsknapper og funksjoner 1.
Page 40 and 41: TIMER OFF DAY DAY SEG Fig. 11 MODE
Page 42 and 43: 4. Driftsmodi Avkjøling I samsvar
Page 44: www.johnsoncontrols.com

EUKC-09, 12, 18 AA - Johnson Controls

Create successful ePaper yourself

Delete template?

Save as template?