INSTRUCTION MANUAL - Virtasenkauppa.fi

More documents

Recommendations

Info

Backhoe technical specifications 60 cm Backhoe technical specifications A B C D E F G H I J K Digging depth ( 60 cm flat bottom) Reach from the center line of swing pivot Loading height (bucket 60°) Maximum levelling angle Swing arc Transporting height (Max.) Transport overhang Bucket rotation Stabilizer spread (down position) Stabilizer spread (up position) Angle of departure Shipping weight (without bucket) Bucket digging force Dipperstick digging force Operating pressure 2200 mm 3200 mm 1850 mm 10° 180° 2120 mm 1230 mm 180° 1750 mm 1180 mm 21° 415 kg 1175 kg 895 kg 160 bar Cylinder Bore diameter Retracted length Stroke Rod diameter Boom 70 mm 620 mm 384 mm 40 mm Bucket 60 mm 535 mm 299 mm 35 mm Dipperstick 60 mm 597 mm 377 mm 35 mm Swing 60 mm 398 mm 223 mm 35 mm Stabilizer 60 mm 446 mm 262 mm 35 mm
Bucket Bucket Tooth Qty Struck capacity Heaped capacity Shipping weight 12” / 30 cm 3 0,3 m3 0,38 m3 35 kg Specifications may vary depending on tractor model, tire size or bucked used. Preparing tractor The purpose of this manual is to assist in setting up, operating and maintaining your backhoe. Read it carefully. It furnishes information and instructions that will help you achieve years of dependable performance. The illustrations and data used in this manual were current (according to the information available to us) at the time of printing, however, we reserve the right to redesign and change the backhoes as may be necessary without notification. Prepare tractor WARNING Never let anyone operate this tractor and backhoe without first reading the safety precaution and operating instruction sections of this manual. Always choose hard, level ground to park the tractor on and set the brake so that the tractor cannot roll. Before you install a 3-point hitch backhoe on any tractor, there are certain critical points that must be checked. Failure to address these points could result in serious damage to the equipment, and serious injury or even death to the operator. Do NOT attempt to install the backhoe until you have gone through the following points and made any corrections to the equipment that might be deemed necessary. Preliminary check The first point to consider is if there will be adequate clearance between the backhoe operator and the tractor. Proper clearance is essential for operator safety. When mounted, there must be a minimum of 60 cm horizontal clearance (with seat in forward position), and a minimum of 72 cm horizontal clearance (with seat in the extended position). There must also be a minimum vertical clearance of 20 cm between the operator's head and any portion of the tractor. Follow the procedure below to check for minimum clearances. 1. With the tractor 3-point hitch lower links set approximately 20-23 cm off the ground, measure the horizontal distance between the lower link ball joint and any object that comes the closest to interfering with the backhoe seat (such as the ROPS or cab). 2. To check the vertical clearance, first make sure the lower links are approximately 20-23 cm off the ground. Measure the vertical distance between the lower link ball joint center and any solid object that could interfere with the backhoe operator's head (such as the tractor cab or ROPS). The distance found must be at least 2 m. This distance allows for the height of the backhoe, the height of the seated operator, and the minimum 20 cm clearance. This figure assumes the operator is 183 cm tall. You will have to add 1cm for every 3 cm your operator is over 183 cm to achieve the correct figure. The distance found must be greater than this distance to safely operate the backhoe. Do not mount the backhoe if the distance found is less than the 198 cm minimum. CAUTION Do not exceed the manufacturer's rating for maximum gross vehicle weight. Refer to operator's manual or ROPS serial plate provided with tractor. Certain specific conditions may not permit safe use of backhoe at backhoe rating or may require more careful restricted operation at the rated load. Tractor ROPS system Tractor must be equipped with an approved ROPS System to ensure adequate operator's protection. Tractor Hydraulic System Tractor operation in a backhoe application significantly increase demands on the tractor hydraulic system. Check the tractor hydraulic system fluid level daily. Refer to your tractor operator's manual maintenance
Page 1 and 2:
Lue käyttöohjeet huolellisesti en
Page 3 and 4:
Alkusanat Onnittelumme tämän laad
Page 5 and 6:
10. Älä koskaan seiso, kävele ta
Page 7 and 8:
VAROITUS Älä koske kaivurin ohjaa
Page 9 and 10:
Sijainti: Oikean puolen venttiili v
Page 11 and 12:
Kauha Kauha Hampaiden lkm Iskukapas
Page 13 and 14:
11. Nosta kaivuri tukijalkojen ja p
Page 15 and 16:
Kaivaminen Kaivurin käyttöönotto
Page 17 and 18:
Erikoissovellukset Ojan kaivaminen
Page 19 and 20:
ohjaamosta. Jälleenmyyjä tarvitse
Page 21 and 22:
Käytä hydrauliikka järjestelmäs
Page 23 and 24:
Matala hydrauliikkanesteen taso. J
Page 25 and 26:
Hydrauliikkapumpun kapasiteetti rii
Page 27 and 28:
Istuimen ja ohjauksen räjäytyskuv
Page 29 and 30:
Rungon räjäytyskuva Kääntörunk
Page 31 and 32:
Kääntörungon räjäytyskuva Pä
Page 33 and 34: Kauhan ja kaivuvarren räjäytyskuv
Page 35 and 36: Letkuliittimen räjäytyskuva Vasen
Page 37 and 38: Hydrauliikkajärjestelmäkaavio Puo
Page 39 and 40: Innehållsförteckning SE 1. Föror
Page 41 and 42: Varningstriangel Denna symbol betyd
Page 43 and 44: VARNINGARNA Transportering av gräv
Page 45 and 46: 4. Om sådant del bytas som innehå
Page 47 and 48: Grävarens tekniska data 60 cm Grä
Page 49 and 50: VARNING Överskrida inte av tillver
Page 51 and 52: Inkoppling av grävaren på traktor
Page 53 and 54: Uppvärmning Innan du börjar anvä
Page 55 and 56: Användning vid kall väderlag För
Page 57 and 58: Servicetabell Del Service Servicepe
Page 59 and 60: Smörja dagligen: Cylindrar för sk
Page 61 and 62: Leder för styrspakar felaktiga Kon
Page 63 and 64: Scheman och sprängbilder Scheman
Page 65 and 66: Nr Produktnummer Beskrivning St. 12
Page 67 and 68: Nr Det nr Beskrivning St. 50 BK215.
Page 69 and 70: Sprängbild över bommen Nr Det nr
Page 71 and 72: Nr Det nr Beskrivning St. 114 GB578
Page 73 and 74: 157 BK215.046 Cylinder för grävar
Page 75 and 76: Scheman över hydrauliksystem Väns
Page 77 and 78: Preface We congratulate you on choo
Page 79 and 80: 12. Before swinging the backhoe, ma
Page 81 and 82: WARNING The important thing for an
Page 83: Location: Main valve cover Location
Page 87 and 88: ATTENTION! Until the backhoe is sec
Page 89 and 90: Dipperstick/Bucket Lever (Right han
Page 91 and 92: When digging a pipe leak, always di
Page 93 and 94: Boom lock When transporting or dism
Page 95 and 96: Note: When checking hydraulic syste
Page 97 and 98: Cylinders operate in wrong directio
Page 99 and 100: External hydraulic fluid leakage Lo
Page 101 and 102: Seat, control assembly exploded vie
Page 103 and 104: Main frame assembly exploded view N
Page 105 and 106: Swing frame assembly exploded view
Page 107 and 108: Bucket, dipperstick assembly explod
Page 109 and 110: Hose fitting assembly exploded view
Page 111 and 112: Hydraulic system assembly Boom Cyli
Page 113: EY-VAATIMUSTENMUKAISUUSVAKUUTUS Iso
show all

INSTRUCTION MANUAL - Virtasenkauppa.fi

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?