BRUSA Elektronik AG info@brusa
BRUSA Elektronik AG info@brusa
BRUSA Elektronik AG info@brusa
Sie wollen auch ein ePaper? Erhöhen Sie die Reichweite Ihrer Titel.
YUMPU macht aus Druck-PDFs automatisch weboptimierte ePaper, die Google liebt.
Betriebsanleitung BSC624-12V User’s manual BSC624-12V<br />
6.2 Zuverlässigkeit<br />
Reliabilty<br />
6.2.1 Überlastschutz - Derating<br />
Overload protection – derating<br />
Rückregelung aufgrund Trafotemperatur<br />
Derating due to transformer temperature<br />
ILVmax/A<br />
250<br />
106<br />
-10A/°C<br />
131<br />
T/°C<br />
Rückregelung aufgrund Schaltertemperatur<br />
Derating due to switch temperature<br />
ILVmax/A<br />
250<br />
95<br />
-10A/°C<br />
120<br />
T/°C<br />
Abschalten aufgrund Schaltertemperatur<br />
von Hoch-/Tiefsetzsteller<br />
Shut down due to temperature of buck/boost<br />
switch<br />
ILVmax/A<br />
250<br />
80 81<br />
T/°C<br />
• Um<br />
das Gerät vor Überlastung zu schützen, wird die<br />
Temperatur von einzelnen Bauteilen erfasst, sodass<br />
bei Erreichen eines bestimmten Werts automatisch<br />
der maximal mögliche Strom zurückgeregelt wird.<br />
Folgende Bauteiltemperaturen werden hierfür erfasst<br />
und verarbeitet:<br />
Schalter der Trafostufe, HV-seitig (2 von 8)<br />
Schalter der Trafostufe, LV-seitig (2 von 8)<br />
Wicklung der HF-Transformatoren (2 von 2)<br />
• Aufgrund der niedrigen Verluste der Schalter des<br />
Hoch-/Tiefsetzstellers sowie der effizienten Kühlung<br />
weist diese gemessene Schaltertemperatur nur eine<br />
geringfügige höhere Temperatur gegenüber jener der<br />
Kühlflüssigkeit auf. Daher gibt diese Temperatur<br />
auch Aufschluss über die im Gerät vorherrschende<br />
Umgebungstemperatur. Damit Bauteile keinen Schaden<br />
nehmen können bzw. deren Lebensdauer nicht<br />
negativ beeinflusst wird, wird das Gerät bei einer<br />
Temperatur von 81°C abgeschaltet. Erst, wenn die<br />
Temperatur wieder unter 80°C sinkt, kann das Gerät<br />
wieder eingeschaltet werden.<br />
Schalter des Hoch-/Tiefsetzstellers (2 von 8)<br />
• Da über die CAN-Schnittstelle der aktuell transferierbare<br />
Strom (LVCUR_AVL) zurückgemeldet wird, ist<br />
erkennbar, ob das Gerät im Rückregelmodus ist.<br />
• Wenn das Gerät aufgrund zu hoher Temperaturen<br />
schlussendlich abschaltet, wird ein entsprechender<br />
Fehler ausgegeben (E_OVERTEMP).<br />
BSC624-12V_User_Manual_090615.doc 22 / 41<br />
• In order to protect the device in case of overload,<br />
the temperature of specific components is monitored,<br />
so that as soon as a certain value is<br />
reached, the maximum available current will be<br />
automatically derated. Following temperatures are<br />
measured and processed:<br />
Switch of transformer stage, HV-side (2 of 8)<br />
Switch of transformer stage, LV-side (2 of 8)<br />
Coil of HF-transformers (2 of 2)<br />
• Due to the low losses of the switches of the<br />
buck/boost-converter as well as due to the efficient<br />
cooling the measured temperature of this<br />
switch shows only a little higher temperature referred<br />
to the that of the coolant. Therefore this<br />
temperature gives information about the predominating<br />
ambient temperature inside the device. In<br />
order to protect components from damage, respectively<br />
to avoid negative impact on their lifetime,<br />
the device will be shut off at a temperature of<br />
81°C. As soon as the temperature decreases below<br />
80°C, the device can be switched on again.<br />
Switch of buck/boost stage (2 of 8)<br />
• Since the actual available current that can be<br />
transferred will be communicated by CAN<br />
(LVCUR_AVL), it can be detected, if the device is<br />
in derating-mode.<br />
• If the device finally shuts off because of too high<br />
temperatures, an error is set (E_OVERTEMP).