A B C D

HSK A-ER-M (Mini)
DIN6499 ER-Mini-Spannzangenfutter
A 0.003 A 58-60 HRc √N5
SS
D2
J
CSI
D3
d min
max
G2.5
HSK A63=20,000RPM
G6.3
HSK A100=12,000RPM
L1Ref
LRef
L3Ref
.
Bezeichnung SS CSI d min d max D3 D2 L L1 L3 J Kg
HSK A 50 ER16X100 M (1) 50 ER16 0.5 10.0 22.00 - 100.00 74.0 - M10 0.60
HSK A 50 ER16X120 M (1) 50 ER16 0.5 10.0 22.00 - 120.00 94.0 - M10 0.60
HSK A 50 ER20X100 M (1) 50 ER20 1.0 13.0 28.00 - 100.00 74.0 - M12 0.61
HSK A 50 ER20X120 M (1) 50 ER20 1.0 13.0 28.00 - 120.00 94.0 - M12 0.69
HSK A 63 ER16X100 M (1) 63 ER16 0.5 10.0 22.00 - 100.00 74.0 - M10 0.80
HSK A 63 ER16X120 M (1) 63 ER16 0.5 10.0 22.00 40.00 120.00 94.0 78.00 M10 0.94
HSK A 63 ER16X160 M (1) 63 ER16 0.5 10.0 22.00 40.00 160.00 134.0 85.00 M10 1.26
HSK A 63 ER20X100 M (1) 63 ER20 1.0 13.0 28.00 - 100.00 74.0 - M12 0.85
HSK A 63 ER20X120 M (1) 63 ER20 1.0 13.0 28.00 - 120.00 94.0 - M12 0.92
HSK A 63 ER20X160 M (1) 63 ER20 1.0 13.0 28.00 45.00 160.00 134.0 85.00 M12 1.48
HSK A 100 ER16X100 M (2) 100 ER16 0.5 10.0 22.00 - 100.00 71.0 - M10 2.16
HSK A 100 ER16X160 M (2) 100 ER16 0.5 10.0 22.00 40.00 160.00 131.0 85.00 M10 2.65
HSK A 100 ER20X100 M (2) 100 ER20 1.0 13.0 28.00 - 100.00 71.0 - M12 2.22
HSK A 100 ER20X160 M (2) 100 ER20 1.0 13.0 28.00 50.00 160.00 131.0 85.00 M12 2.82
• Bei HSK Kühlung durch die Spindel muss grundsätzlich ein Kühlmittelrohr verwendet werden (muss separat bestellt werden).
(1) Gewuchtet auf G2.5/20.000 min -1 . (2) Gewuchtet auf G6.3/12.000 min -1 .
B145-148 B175 B177 B176, B180 B180 B142-144
B30
ISCAR