WEW 400 - Küppersbusch

Weitere Magazine

Empfehlungen

Info

• • • • 1 • • • 3 • 2 • • • • • • • 1 1 • • • • • • 3 • • • 3 • 2 2 • • • • • • • • Dimensions C B C B C B F F WEW 400 mm 400x610x...... Weight 17 Kg WEW 600 mm 620x610x...... Weight 23,2 Kg C B A D E F G H Swicht Load lever Water filling tap Water outlet Pilot lamp Electric connection EL Water inlet ø 12 Selector switch Technical data The data plate is located on the front of the appliance and contains all the data needed for connecting it up to the mains electricity supply. Electrical data Model WEW 400 WEW 600 Voltage rating 400 V 3N AC or 230 V 3 AC Power 4,5 kW 6,9 kW Lead wire / Section 4 x 1,5 mm 2 or 5 x 1,5 mm 2 18 WEW WR.NR. BI.18
Installation instructions Installation Before beginning installation, remove all packaging from the appliance. Some parts are protected with an adhesive film which should be carefully removed. Any remnants of glue should be thoroughly cleaned using suitable substances such as benzine. Under no circumstances should abrasive substances be used. Fit the legs to the appliance; the appliance must be levelled using a spirit level. Slight irregularities can be levelled by adjusting the feet themselves. With table models, make sure that the base chosen is capable of supporting the weight of the appliance. The main switch or plug should be located in the vicinity of the appliance and easy of access. We recommend installing the machine under a range hood so that all the fumes are removed as quickly as possible. If the appliance is to be installed near walls, dividing walls, kitchen equipment or decorative pannelling, these should be in noninflammable material or covered with non-inflammable material. Make sure that all fire prevention standards and safety precautions are strictly adhered to. Warning! ! With Top models, carefully measure the distance between the appliance and the edge of the base (Fig. 2). Legal and technical requisites When installing the appliance, the following safety standards must be adhered to: - Local accident prevention standards - Current CEI standards. Installation Installation, start-up and maintenance should only be carried out by expert personnel. All work required to install the appliance should be carried out in compliance with all local standards and regulations. The manufacturers decline all responsibility where poor performance is due to incorrect installation in disregard of the above conditions. Warning! ! Wiring In compliance with international regulations, when connecting the appliance to the mains power supply, a device with a minimum aperture of 3 mm between contacts must be fitted upstream of the appliance, allowing omnipolar disconnection of the appliance from the mains. When choosing the lead wire, make sure it has the following characteristics: it should be at least of the H07 RN-F type and its section should be large enough for the appliance (see "Technical specifications and dimensions"). Wire entry on top models is on the back wall, and underneath all other models. In both cases the terminal board is at the front, behind the control panel. Pass the wire through the core hitch and wire clamp, plug the leads into their terminals on the board and secure them. The earth lead must be a little longerthan the others so that it is the last lead to disconnect if the wire clamp breaks. Unipotential The appliance must be connected up to a unipotential system. The connection screw is located on all top models at the back on the right hand side, while in other models it is located underneath the appliance on the right hand side. It is labelled. Connection to waterworks - Water inlet pressure must be between 50 and 300 kPa, otherwise install a pressure regulator on the line before the appliance. - Install a cut-off valve for each supply on the line before the appliance. - Make connections according to regulations currently in force. Warning! ! ! The manufacturers cannot be held responsible for any damage due to inadequate or incorrect installation. Under such circumstances the guarantee will be considered null and void. WEW WR.NR. BI.19 19
Seite 1 und 2: Betriebs- und Installationsanleitun
Seite 3 und 4: Inhaltsverzeichnis Kundendienst . .
Seite 5 und 6: Angaben zum Gerät Diese Geräte si
Seite 7 und 8: Aufstellung Bevor man mit den Aufst
Seite 9 und 10: Ø7 Ø7 3 3 616 585 616 585 406 360
Seite 11 und 12: Betriebsanleitung Sicherheitshinwei
Seite 13 und 14: Arbeitsgrundsätze für Geräte aus
Seite 15 und 16: Pos. Benennung Teile-Nr Stück bei
Seite 17: Index Models and dimensions . . . .
Seite 21 und 22: Precautions during use Sauces and c
Seite 23 und 24: Pos. Description Notes Item-No. REW
Seite 25 und 26: Inhoudsopgave Schematische weergave
Seite 27 und 28: Instructies voor de installatie Ger
Seite 29 und 30: Voorzorgsmaatregelen tijdens het ge
Seite 31 und 32: Pos. Benaming Opmerking Res.deel-nr
Seite 33 und 34: Index Répresentation schématique
Seite 35 und 36: Instruction pour l’intallation Mi
Seite 37 und 38: Précautions en cours d'emploi Sauc
Seite 39 und 40: Pos. Description Notes Article n. R
Seite 41: Küppersbusch Großküchentechnik G

WEW 400 - Küppersbusch

Sie wollen auch ein ePaper? Erhöhen Sie die Reichweite Ihrer Titel.

Template löschen?

Als Template speichern?