Montage- und Betriebsanleitung Operation and Assembly Instruction
Montage- und Betriebsanleitung Operation and Assembly Instruction
Montage- und Betriebsanleitung Operation and Assembly Instruction
Erfolgreiche ePaper selbst erstellen
Machen Sie aus Ihren PDF Publikationen ein blätterbares Flipbook mit unserer einzigartigen Google optimierten e-Paper Software.
- Beachten Sie die Phasenfolge!<br />
Bei der <strong>Montage</strong> der Kabel dürfen keine<br />
Zug- <strong>und</strong> Biegebeanspruchungen auf die<br />
Anschlusskonen entstehen!<br />
- Montieren Sie die Phase L1 <strong>und</strong> befestigen Sie<br />
das Kabel mit geeigneten Kabelschellen am<br />
Kabelhalteeisen so, dass das Kabel senkrecht<br />
nach unten ragt. Montieren Sie dann Phase L2<br />
<strong>und</strong> zum Schluss Phase L3 entsprechend.<br />
- Überprüfen Sie den Zust<strong>and</strong> der Endverschlüsse,<br />
z.B. Oberflächenbeschaffenheit,<br />
ordnungsgemäße Anordnung der Kabelschuhe<br />
<strong>und</strong> Klemmverbindungen.<br />
- Kabelschirme an den Erdungsschrauben des<br />
Kabelhalteeisens erden. Beachten Sie die Sicherheits-<br />
<strong>und</strong> <strong>Montage</strong>hinweise des Herstellers<br />
der Kabelgarnituren!<br />
- Befestigen Sie die Kabel an der mitgelieferten<br />
oder bauseitig angebrachten Endverschlusstraverse!<br />
Das maximale Anzugsmoment für den<br />
Kontaktanschlussbolzen beträgt 60Nm!<br />
Das zulässige Drehmoment für die<br />
Endverschlüsse beachten!<br />
Bei Verwendung von Schrumpfend-<br />
verschlüssen muss das oberhalb des<br />
Endverschlusses montierte Kabelhalteblech<br />
gegen zu hohe Wärme geschützt werden.<br />
Vermeiden Sie langfristige lokale<br />
Erwärmungen.<br />
DRIESCHER • WEGBERG<br />
- Observe the phase sequence!<br />
Prevent tensile <strong>and</strong> bending stress to<br />
the connection cones during the cable<br />
assembly!<br />
- Assemble phase L1 <strong>and</strong> fix the cable with suitable<br />
cable clamps onto the cable holding iron<br />
in such a way that the cable extends vertically<br />
downwards. Then assemble phase L2 <strong>and</strong><br />
finally phase L3.<br />
- Check the state of the terminals, i.e. the state<br />
of the surfaces, the right location of the cable<br />
lugs <strong>and</strong> the clamps.<br />
- Earth the cable shields at the earthing screws<br />
of the cable holding iron. Respect the safety<br />
<strong>and</strong> assembly instructions of the cable producer.<br />
- Fix the cables on the supplied cable box carrier<br />
or same provided at site.<br />
The maximum torque for the contact nut<br />
is 60Nm!<br />
Observe the admissible torque of the<br />
terminals!<br />
With use of heat shrink terminations the<br />
cable holding sheet situated above the<br />
terminal has to be protected against<br />
overheating.<br />
Avoid long-termed local temperature rises.<br />
MINEX / G.I.S.E.L.A 27