Film & Digital Times Issues 36-38 - Imago

More documents

Recommendations

Info

Cameras 6 Dec 2010
Sensor Sensibility “Check the Gate.” Even after endless takes of the same scene, in which a director numbingly has actors repeat the same lines, the AD’s exhortation to move on is not “Check the script.” The AD asks the AC to remove the lens, peer inside the film camera cavity, and declare that all is well. Or not. If there’s a speck of dust anywhere in the picture area, the dreaded words ring out, “Hair in the gate,” and with a groan, the scene is usually repeated again. Digital cameras aren’t much different. You should check the gate as carefully and as often. Sometimes you can see smudges or specks on a good monitor. But not always. Therefore, whenever you change lenses, be careful about dirt or dust flying into the lens cavity. Watch out on windy days. Check the sensor the way you checked the gate on film cameras: with a lighted magnifier. An excellent magnifier is included in the LensPen SensorKlear Loupe Kit. It focuses, the light is LED, and there’s an opening on the side with access to clean the sensor. (www.lenspen.com) Digital sensors are protected by an expensive, coated cover glass and low-pass filter pack. This is what we’ll be cleaning, and it should not be the untouchable, forbidden territory we’ve been warned about. It’s a piece of glass very much like coated lens elements or mirror shutters we’ve cleaned before. We’re not touching the individual photosites of the sensor—they are mercifully protected by this cover glass. Cleaning the cover glass of sensors is delicate business, and there lurks great potential for great damage. It’s still best to leave this to skilled camera technicians. If you’re not comfortable with it, don’t do it. If the World’s Worst Assistant is working on your job, keep him away. But, more likely, you’re shooting on the Skeleton Coast of Namibia. The wind is howling, the salt spray and sand are flying, and something’s on the sensor from the previous lens change. You’re 1,100 miles away from Jannie van Wyk at Media Film Services in Cape Town. Are you feeling lucky? While there are as many opinions on cover glass filter cleaning as a New York cabbie’s opinions on the best route crosstown, I have several favorites. Remember, these are personal opinions. Test it on an inexpensive stand-in sensor first. It goes like this, in steps. 1. Use the illuminated magnifier to determine what kind of schmutz is on the cover glass. It’s usually either dry or sticky. 2. Peter Meurrens, VP Operations of Parkside Optical (makers of SensorKlear) says, “About 75% of the time a simple use of the hand blower solves the problem. It is quick and you do not actually touch the sensor surface. By holding the camera upside down, gravity and vortex swirl of the blower in the chamber takes the dust outside. Anything remaining after use of the blower is, by definition, stickier dust.” 3. For stickier dust, use a LensPen. LensPens have been the winners of the Camera Cleaning Olympics held periodically and unofficially since 2000. They come in many shapes —our favorite is the new SensorKlear-II. It has a right-angle probe fitted with a small mushroom-shaped micro-fiber tip that contains carbon black to “wick” contaminants away from surfaces like lenses and cover glasses. Meurrens explains, “The function of the LensPen SensorKlear-II is to make the sticky dust particle stop sticking. Most of the sticky dust is held in place by static electricity or by a small bit of moisture caused by humidity. The SensorKlear-II Cleaning Pad has 3 corners—used for getting into the 90° corner of the sensor surface. It also has 3 sides; I like to use these edges to lightly ‘kick’ the sticky dust particle by approaching it from the side. The dust particle will either stick to the cleaning pad and I take it out and blow it away, or the dust particle will move, i.e., stop sticking. I do not use the flat surface of the Cleaning Pad as I do not want to push the dust particle down onto the sensor surface.” 4. After removing sticky dust with the SensorKlear-II, use the hand blower to blow dust off the cleaning tip. One SensorKlear-II can last up to 200 cleanings, but at $24 each, it’s an inexpensive replacement to begin fresh with each job. What will severely shorten the useful life of the Cleaning Tip is to clean the messy residue left on the sensor surface by other products. For that, use Pancro. 5. Pancro Lens Cleaning Fluid has been the perennial runner-up in the Camera Cleaning Olympics, and a longtime favorite for lenses, mirror shutters and eyepieces. Use Pancro if the speck on your sensor is salt spray, a stubborn stain, or gooey residue that requires a liquid solvent. Use sparingly. You don’t want the fluid to leak around the cover glass and onto the sensor’s photosites. (www.pancro.com) Apply Panchro with ITW Texwipe TX762 Swabs. These are lint-free swabs for cleaning microscopes. (www. texwipe.com and www.soscleanroom.com) Dec 2010 7
Page 1 and 2: Jon Fauer’s www.fdtimes.com Dec 2
Page 3 and 4: 2010: Gear this Year exposure adjus
Page 5: Martin Hartweg: Cinec Top Chef A sp
Page 9 and 10: Alexa Tour One hundred cameras...an
Page 11 and 12: Flange Focal Depth Image Testing Th
Page 13 and 14: A Brief Illustrated History of Alex
Page 15 and 16: Interview with Franz Kraus This ide
Page 17 and 18: ARRI at IBC and Cinec ARRI Alexa Si
Page 19 and 20: Sony SRW-9000PL Camera Views Existi
Page 21 and 22: Sony PMW-F3 This is not a tape meas
Page 23 and 24: Sony PMW-F3 The right side of the c
Page 25 and 26: Aaton Penelope Delta Aaton Penelope
Page 27 and 28: P+S Technik P+S Technik’s Alfred
Page 29 and 30: Camera: Work in Progress A big surp
Page 31 and 32: Phantom Flex Why do we call digital
Page 33 and 34: Converging Stills Sony NEX-5 Fujifi
Page 35 and 36: FGV PL1D FGV PL5D They weren’t go
Page 37 and 38: Canon Expo: 4K The 4K race accelera
Page 39 and 40: NHK 8K with Fujinon Lens Plan ahead
Page 41 and 42: RED Epic The original, revolutionar
Page 43 and 44: Storage: Marvin Cinedeck Alan Hoff,
Page 45 and 46: 3D P+S Technik Freestyle Rig for St
Page 47 and 48: Lenses Dec 2010 47
Page 49 and 50: Angénieux Optimo Zooms The Optimo
Page 51 and 52: Image Stabilization by Larry Thorpe
Page 53 and 54: ARRI/Fujinon Alura PL Zooms ARRI/ZE
Page 55 and 56: ARRI/ZEISS Ultra Prime Lenses Ultra
Page 57 and 58:
ZEISS Lightweight Zoom LWZ.2 Focal
Page 59 and 60:
Cooke 5/i Cooke 5/i Primes are all
Page 61 and 62:
Cooke Panchro/i Cooke Panchro/i Pri
Page 63 and 64:
Leica Factory Tour The Summilux-C C
Page 65 and 66:
Vantage Hawk Anamorphics Vantage co
Page 67 and 68:
ARRI Lighting LoCaster LED. Ryan Fl
Page 69 and 70:
Litepanels Ianiro Ianiled Rudy Pohl
Page 71 and 72:
Dedolight PanAura PanAura dedicated
Page 73 and 74:
Lighttools Soft Egg Crates Airstar
Page 75 and 76:
Moviecam EasyFocus Fritz Gabriel Ba
Page 77 and 78:
Transvideo HDMI Serial receptacles
Page 79 and 80:
Get a Grip on your O-Box OConnor ha
Page 81 and 82:
Petrol Kinomatik Schultz Spray Defl
Page 83 and 84:
Preston Cinema Systems Preston Cine
Page 85 and 86:
K-Tek Screen Plane Sebastian Cramer
Page 87 and 88:
Denz FDC Cineparts All PL Mount len
Page 89 and 90:
Steadicam Smoothee from Tiffen Rele
Page 91 and 92:
OConnor 2065 Sachtler artemis Ronfo
Page 93 and 94:
Cartoni Maxima New from Cartoni: Ma
Page 95 and 96:
Andy’s Skycam FF Andy from Italy
show all

Film & Digital Times Issues 36-38 - Imago

Create successful ePaper yourself

Delete template?

Save as template?