MVME5500 Single-Board Computer Installation and Use - Bustec

More documents

Recommendations

Info

xx , or Ctrl represents the carriage return or Enter key. represents the Control key. Execute control characters by pressing the Ctrl key and the letter simultaneously, for example, Ctrl-d.
Introduction Description 1Hardware Preparation and Installation This chapter contains the following information: ❏ Board preparation and installation instructions ❏ ESD precautionary notes 1 The MVME5500 is a single-board computer based on the PowerPC MPC7455 processor and the Marvell GT-64260B host bridge with a dual PCI interface and memory controller. On-board payload includes two PMC slots, two SDRAM banks, an expansion connector for two additional banks of SDRAM, 8MB boot Flash ROM, one 10/100/1000 Ethernet port, one 10/100 Ethernet port, 32MB expansion Flash ROM, two serial ports, NVRAM and a real-time clock. The MVME5500 interfaces to a VMEbus system via its P1 and P2 connectors and contains two IEEE 1386.1 PCI mezzanine card (PMC) slots. The PMC slots are 64-bit and support both front and rear I/O. Additionally, the MVME5500 is user-configurable by setting on-board jumpers. Two I/O modes are possible: PMC mode or SBC mode (also called 761 or IPMC mode). The SBC mode uses the IPMC712 I/O PMC and the MVME712M transition module, or the IPMC761 I/O PMC and the MVME761 transition module. The SBC mode is backwards compatible with the MVME761 transition module and the P2 adapter card (excluding PMC I/O routing) used on the MVME5100 product. This mode is accomplished by configuring the on-board jumpers and by attaching an IPMC761 PMC in PMC slot 1. Secondary Ethernet is configured to the rear. PMC mode is backwards compatible with the MVME5100 and is accomplished by configuring the on-board jumpers. 1-1
Page 1 and 2: MVME5500 Single-Board Computer Inst
Page 3 and 4: Safety Summary The following genera
Page 5 and 6: Warning ! Warning CE Notice (Europe
Page 7 and 8: Contents About This Manual Summary
Page 9 and 10: System Memory .....................
Page 11 and 12: APPENDIX D Related Documentation Mo
Page 13 and 14: List of Tables Table 1-1. Startup O
Page 15 and 16: About This Manual The MVME5500 Sing
Page 17: Comments and Suggestions Motorola w
Page 21 and 22: Caution ESD Caution Warning ! Cauti
Page 23 and 24: MVME5500 Preparation For pin assign
Page 25 and 26: PMC 2 PMC 1 ABT/RST GigE 10/100 CPU
Page 27 and 28: Warning Ethernet 2, PMC/SBC Mode, a
Page 29 and 30: Flash Boot Bank Select Header (J8)
Page 31 and 32: SROM Initialization Enable Header (
Page 33 and 34: VME SCON Select Header (J27) VME SC
Page 35 and 36: Hardware Installation Installing th
Page 37: Completing the Installation Complet
Page 40 and 41: 2 Startup and Operation The MVME550
Page 42 and 43: 3 MOTLoad Firmware unique MOTLoad b
Page 44 and 45: 3 MOTLoad Firmware Using MOTLoad In
Page 46 and 47: 3 MOTLoad Firmware Example MVME5500
Page 48 and 49: MOTLoad Firmware Table 3-1. MOTLoad
Page 50 and 51: MOTLoad Firmware Table 3-1. MOTLoad
Page 52 and 53: 3 MOTLoad Firmware VME Settings As
Page 54 and 55: 3 MOTLoad Firmware ❏ PCI Slave Im
Page 56 and 57: 3 MOTLoad Firmware CR/CSR Settings
Page 58 and 59: 3 MOTLoad Firmware Deleting VME Set
Page 60 and 61: 3 MOTLoad Firmware The selection of
Page 62 and 63: 4 Functional Description Interrupt
Page 64 and 65: 4 Functional Description MVME5500 p
Page 66 and 67: 4 Functional Description and initia
Page 68 and 69:
4 Functional Description PCI Local
Page 70 and 71:
4 Functional Description Asynchrono
Page 72 and 73:
4 Functional Description PMC Expans
Page 74 and 75:
5 Pin Assignments Connectors ❏ Bu
Page 76 and 77:
5 Pin Assignments Table 5-3. IPMC C
Page 78 and 79:
5 Pin Assignments Table 5-4. PCI/PM
Page 80 and 81:
5 Pin Assignments CPU COP Connector
Page 82 and 83:
5 Pin Assignments Table 5-6. PMC 1
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
5 Pin Assignments PMC 2 Interface C
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
5 Pin Assignments Asynchronous Seri
Page 96 and 97:
5 Pin Assignments Table 5-16. VME C
Page 98 and 99:
5 Pin Assignments J102 - J110 shoul
Page 100 and 101:
5 Pin Assignments Table 5-18. VME C
Page 102 and 103:
5 Pin Assignments Table 5-19. Memor
Page 104 and 105:
5 Pin Assignments Table 5-19. Memor
Page 106 and 107:
5 Pin Assignments PMC/SBC Mode Sele
Page 108 and 109:
5 Pin Assignments I/O for P2 in SBC
Page 110 and 111:
5 Pin Assignments MVME761 Transitio
Page 112 and 113:
5 Pin Assignments Flash Boot Bank S
Page 114 and 115:
5 Pin Assignments SROM Initializati
Page 116 and 117:
5 Pin Assignments VME SCON Select H
Page 118 and 119:
Power Requirements ASpecifications
Page 120 and 121:
BRAM5500 Memory Expansion Module Ov
Page 122 and 123:
SROM Clocks SROM The RAM5500 memory
Page 124 and 125:
Memory Expansion Connector (P1) Pin
Page 126 and 127:
Memory Expansion Connector (P1) Pin
Page 128 and 129:
CThermal Validation C Board compone
Page 130 and 131:
PMC 2 PMC 1 ABT/RST GigE 10/100 CPU
Page 132 and 133:
Component Temperature Measurement C
Page 134 and 135:
Thermocouple junction bonded to com
Page 136 and 137:
DRelated Documentation Motorola Com
Page 138 and 139:
Table D-2. Manufacturers’ Documen
Page 140 and 141:
Related Specifications Related Spec
Page 142 and 143:
I N D E X headers, setting 1-5 heat
show all

MVME5500 Single-Board Computer Installation and Use - Bustec

Create successful ePaper yourself

Delete template?

Save as template?