Bedienungsanleitung Graupner JR mx-12 (englische Version) - ROKE

More documents

Recommendations

Info

Contents General Notes Safety Notes................................................................... 2 Introduction.................................................................... 3 Description of radio control system................................ 7 Charging the transmitter battery..................................... 8 Transmitter description................................................... 9 Direct servo control.......................................................11 Connections and installations -> For Airplane.............................................................. <strong>12</strong> -> For Helicopter............................................................13 Key input and display.................................................... 14 Alarm and error display................................................. 14 Input mode and function............................................... 15 Program Function mode.............................................................. 16 System mode................................................................17 List mode...................................................................... 18 Function mode AIRPLANE Dual Rates and Exponential......................................... 19 Servo Reversing........................................................... 19 Sub Trim....................................................................... 20 Travel Adjust................................................................. 20 Elevator to flap mixing.................................................. 21 Aileron to rudder mixing............................................... 21 Throttle Cut switch........................................................ 22 Flap System................................................................. 22 Differential aileron mixing............................................. 23 Programmable Mixing (1~4)......................................... 23 Fail Safe....................................................................... 24 Servo Travel Screen..................................................... 25 Function mode HELICOPTER Dual Rates and Exponential.........................................26 Servo Reversing........................................................... 26 Sub Trim....................................................................... 27 2 Contents Travel Adjust................................................................. 27 CCPM Swashplate Mixing............................................ 28 Throttle Cut Switch....................................................... 29 Throttle Hold................................................................. 29 Throttle Curves............................................................. 30 Pitch Curves................................................................. 31 Revolution Mixing (Non-heading lock Gyro only)......... 33 Programmable Mixing (1~2)......................................... 33 Fail Safe....................................................................... 34 Servo Travel Screen..................................................... 35 System Mode Model Selection............................................................ 36 Model Name Entry........................................................ 36 Model Type Selection................................................... 37 Model Copy Function.................................................... 37 Modulation Selection.................................................... 38 Stick Mode.................................................................... 38 Trainer Function............................................................ 39 Switch Select................................................................ 40 Wing Type Selection..................................................... 41 Swashplate Selection................................................... 44 Appendix Approved operating frequencies.................................. 45 Approval Certificate / Conformity.................................. 46 Guarantee certificate.................................................... 47 The sole purpose of this manual is to provide information. It is subject to modification at any time, and must not be considered as any form of obligation on the part of the GRAUPNER company. GRAUPNER accepts no responsibility or liability for errors or inaccuracies which may be found in the information section of this manual. Environ mental Protection Notes When this product comes to the end of its useful life, you must not dispose of it in the ordinary domestic waste. The correct method of disposal is to take it to your local collection point for recycling electrical and electronic equipment. The symbol shown here, which may be found on the product itself, in the operating instructions or on the packaging, indicates that this is the case. Individual markings indicate which materials can be recycled and re-used. You can make an important contribution to the protection of our common environment by re-using the product, recycling the basic materials or recycling redundant equipment in other ways. Remove batteries from your device and dispose of them at your local collection point for batteries. If you don’t know the location of your nearest disposal centre, please enquire at your local council office.
Safety notes Please read carefully! We all want you to have many hours of pleasure in our mutual hobby of modelling, and safety is an important aspect of this. It is absolutely essential that you read right through these instructions and take careful note of all our safety recommendations. If you are a beginner to the world of radio-controlled model aircraft, boats and cars, we strongly advise that you seek out an experienced modeller in your field and ask him for help and advice. These instructions must be handed on to the new owner if you ever sell the transmitter. Application This radio control system may only be used for the purpose for which the manufacturer designed it, i.e. for operating radio-controlled models which do not carry humans. No other type of use is approved or permissible. Safety notes SAFETY IS NO ACCIDENT and … RADIO-CONTROLLED MODELS ARE NOT PLAYTHINGS Even small models can cause serious personal injury and damage to property if they are handled incompetently. Technical problems in electrical and mechanical systems can cause motors to rev up or burst into life unexpectedly, with the result that parts may fly off at great speed, causing considerable injury. Short-circuits of all kinds must be avoided at all times. Short-circuits can easily destroy parts of the radio control system, but even more dangerous is the acute risk of fire and explosion, depending on the circumstances and the energy content of the batteries. The circumstances and the energy content of the batteries. Aircraft and boat propellers, helicopter rotors, open gearboxes and all other rotating parts which are driven by a motor or engine represent a constant injury hazard. Do not touch these items with any object or part of your body. Remember that a propeller spinning at high speed can easily slice off a finger! Ensure that no other object can make contact with the driven components. Protect all electronic equipment from dust, dirt, damp, and foreign bodies. Avoid subjecting the equipment to vibration and excessive heat or cold. Radio control equipment should only be used in „normal“ ambient temperatures, i.e. within the range -15°C to +55°C. Avoid subjecting the equipment to shock and pressure. Check the units at regular intervals for damage to cases and leads. Do not re-use any item which is damaged or has become wet, even after you have dried it out thoroughly. Use only those components and accessories which we expressly recommend. Be sure to use only genuine matching GRAUPNER connectors of the same design with contacts of the same material. Use only genuine GRAUPNER plug-in crystals on the appropriate frequency band. When deploying cables note that they must not be under tension, and should never be bent tightly or kinked, otherwise they may fracture. Avoid sharp edges which could wear through the cable insulation. Check that all connectors are pushed home firmly before using the system. When disconnecting components, pull on the connectors themselves - not on the wires. It is not permissible to carry out any modifications to the RC system components. Avoid reverse polarity and short-circuits of all kinds, as the equipment is not protected against such errors. Installing the receiving system and deploying the receiver aerial In a model aircraft the receiver must be packed in soft foam and stowed behind a stout bulkhead, and in a model boat or car should be protected effectively from dust and spray. The receiver must not make contact with the fuselage, hull or chassis at any point, otherwise motor vibration and landing shocks will be transmitted directly to it. When installing the receiving system in a model with a glowplug or petrol engine, be sure to install all the components in well protected positions so that no exhaust gas or oil residues can reach the units and get inside them. This applies above all to the ON / OFF switch, which is usually installed in the outer skin of the model. Secure the receiver in such a way that the aerial, servo leads and switch harness are not under any strain. The receiver aerial is permanently attached to the receiver. It is about 100 cm long and must not be shortened or extended. The aerial should be routed as far away as possible from electric motors, servos, metal pushrods and high-current cables. However, it is best not to deploy the aerial in an exactly straight line, but to angle it: e.g. run it straight to the tailplane, then leave the final 10 - 15 cm trailing down, as this avoids reception „blind spots“ when the model is in the air. If this is not possible we recommend that you lay out part of the aerial wire in an S-shape inside the model, close to the receiver if possible. Safety notes 3
Page 4 and 5: Safety notes Installing the servos
Page 6 and 7: Computer system mx-12 6 channel dig
Page 8 and 9: Charging the transmitter battery Ch
Page 10 and 11: Transmitter description Transmitter
Page 12 and 13: Connections and installations For A
Page 14 and 15: Key input and display; Alarm and er
Page 16 and 17: Function mode To enter the Function
Page 18 and 19: List mode To enter the Function Lis
Page 20 and 21: Function mode AIRPLANE Sub Trim; Tr
Page 22 and 23: Function mode AIRPLANE Throttle Cut
Page 24 and 25: Function mode AIRPLANE Fail Safe Ac
Page 26 and 27: Function mode HELICOPTER Dual Rate
Page 28 and 29: Function mode HELICOPTER CCPM Swash
Page 30 and 31: Function mode HELICOPTER Throttle C
Page 32 and 33: Function mode HELICOPTER press the
Page 34 and 35: Function mode HELICOPTER Fail Safe
Page 36 and 37: System Mode Model Selection; Model
Page 38 and 39: System Mode Modulation Selection, S
Page 40 and 41: System Mode Switch Select Switch Se
Page 42 and 43: System Mode direction. Note: Each s
Page 44 and 45: System Mode Swashplate Type Selecti
Page 46 and 47: Approval certificate Conformity App

Bedienungsanleitung Graupner JR mx-12 (englische Version) - ROKE

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?