Bedienungsanleitung Graupner JR mx-12 (englische Version) - ROKE
Bedienungsanleitung Graupner JR mx-12 (englische Version) - ROKE
Bedienungsanleitung Graupner JR mx-12 (englische Version) - ROKE
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Function mode HELICOPTER<br />
Throttle Cut Switch; Throttle Hold<br />
Ch6 = Pitch<br />
3 servo (<strong>12</strong>0°)<br />
Ch2 = Aileron<br />
Ch2 = Elevator<br />
Ch6 = Pitch<br />
Throttle Cut Switch<br />
This function assigns the Throttle Cut switch to the push<br />
button located on upper right front of the transmitter.<br />
The Throttle Cut function is designed to return the<br />
throttle trim to the lowest position instantly and keep this<br />
position while the button is pressed. This feature is used<br />
to “cut“ or stop the engine without changing the position<br />
of digital throttle trim.<br />
Go to Throttle Hold<br />
menu<br />
Go to Travel adjust<br />
menu<br />
Throttle Cut Operating position<br />
(-32~-<strong>12</strong>8)<br />
Change value<br />
Set function to Inhibit<br />
Accessing the Throttle Cut Function<br />
1. Place the transmitter power switch in the ON positi-<br />
on.<br />
2. Access the Function mode. To do so, press the<br />
Down ans Select keys simultaneously. Press<br />
either the Up or Down key until THRO CUT ap-<br />
pears in the upper portion of the LCD screen.<br />
3. Us the (+) and (-) keys to change the value of the<br />
Throttle cut function.<br />
Note: Pressing the Clear key will Inhibit the Throttle<br />
Cut, turning it off until it has been reactivated.<br />
4. Access the TRAVEL ADJ mixing function by pres-<br />
sing the Down key.<br />
5. Access the THROTTLE HOLD function by pressing<br />
the Up key.<br />
6. Exit the THRO CUT function by pressing the Down<br />
and Select keys simultaneously.<br />
Throttle Hold<br />
The Throttle Hold function is designed to hold the throttle<br />
servo in a specific position during an autorotation.<br />
This is very useful for practicing autorotation landings.<br />
The throttle hold switch can be programmed to one of<br />
the four toggle switches. Throttle hold will always be<br />
“On“ in the forward switch position and “Off“ in the rear<br />
position.<br />
Go to Throttle Curve<br />
menu<br />
Go to Throttle Cut<br />
menu<br />
Select function to<br />
change<br />
Press +/- key Press CLR key during selecting<br />
SW<br />
Change value/SW<br />
selection<br />
Reset POS value to 0<br />
or Inhibit function<br />
Throttle Hold Position Hold SW Select<br />
(-20~50)<br />
Switch<br />
LEFT : THRO HOLD SW Forward SideOn<br />
AILE D/R : AILE D/R: AILE D/R SW Position 1On<br />
ELEV D/R : ELEV D/R Position 1On<br />
RIGHT : FLIGHT MODE SW Forward SideOn<br />
Accessing the Throttle Hold Function<br />
1. Place the transmitter power switch in the ON positi-<br />
on.<br />
2. Press the Down and Select keys simultaneously<br />
to enter the Function mode.<br />
3. Press either the Up or Down key until THROTTLE<br />
HOLD appears across the top of the LCD.<br />
4. The factory setting for the throttle hold is inhibit.<br />
Pressing either the (+) or (-) key will activate Throttle<br />
Hold and display the current throttle hold value.<br />
5. Using the (+) or (-) key, adjust the throttle hold<br />
value to deliver the proper engine idle rpm for your<br />
helicopter. The adjustable range is (-20% -/+ 50%).<br />
Once you establish the proper idle value for your<br />
engine, you can use this value for throttle hold as<br />
well. To shut the engine off for autorotation, a negati-<br />
ve or zero value should be input.<br />
Note: When the throttle hold is activated, and the<br />
switch is on, the indicator on the LCD will<br />
change from Off to On. In addition, the throttle<br />
trim indicator will be inhibited.<br />
6. Access the THROTTLE CURVE function by pres-<br />
sing the Up key.<br />
Function mode HELICOPTER 29