9363637b, Operating manual HDTV Satellite Receiver ... - Kathrein

More documents

Recommendations

Info

In the event of a malfunction, fi rst check all the cable connections and operating states: 1. Receiver and TV set power plugs are connected to wall socket 2. Antenna cables are connected to the receiver input 3. Receiver and TV set are correctly connected to each other by a HDMI or Scart or cinch cable 4. Audio connections are made to the Hi-Fi or Dolby Digital system as appropriate 5. Receiver and TV set (Hi-Fi/Dolby Digital system) are switched on (check power indicators) 6. Receiver is responding to remote control A selection of troubleshooting tips is offered below. 114 Problem Cause Remedy A “No signal!” warning appears on some or all channels Remote control no longer responding Wrong time being displayed The following channels cut out or “No or bad signal!” appears: DSF, Tele 5, HSE 24 and Sonnenklar TV Troubleshooting Antenna signal of satellite reception system missing or faulty. Incorrect LNB frequencies set in “Antenna Confi guration” menu. Receiver or remote control command set may have been unintentionally changed “Summer Time” setting wrong. An incorrect time was imported from the reception signal DECT telephones operate on the same frequency as these channels. Interference may occur due to inadequate level or poor shielding of cable Consult an antenna specialist to have it checked and repaired as necessary. Check the settings in the “Settings”, “Antenna confi guration” menu, and change them if necessary. Set infrared code 1, as described in the operating manual under “General operating instructions”, “Remote control code”; check batteries On “Settings” - “Date and Time Setup” menu check “Summer Time Enabled” and change as necessary Use the power switch to switch the receiver off from the current channel, e.g. Das Erste or ZDF, wait 10 seconds and then switch it back on Consult your antenna specialist
Technical appendix Type UFS 903si UFS 903sw Order no./colour RF section 20210149/silver 20210137/black Sat IF band MHz 950-2150 Input level band TV system, video dBµV 44-83 Modulation, FEC, demultiplexer DVB-S/DVB-S2 standard Video resolution CCIR 601 (720 x 576 lines), 576i, 576p, 720p, 1080i Video decryption MPEG-2, MPEG-4-compatible Input data rate MSymb/s 2-45, (30 for DVB-S2/8PSK) S/N TV system, audio dB > 53 Decryption AC 3, MPEG 1, Layers 1, 2 and 3 Sampling rate kHz 32/44,1/48 S/N Power Supply dB > 65 Power supply voltage V/Hz 230/50-60 Power consumption (max./standby) W < 27/0.4 LNB supply (horiz./vert.) V/mA 14/18; max. 400 Control signal kHz 22; DiSEqCTM Connections 1.0/-1.1/-1.2/USALS, SCR single cable system Sat IF input/output 2 x F sockets TV/VCR connection 1 x Scart sockets Video output (analogue) 1 x Cinch socket Video/audio output (digital) 1 x HDMI Audio output (analogue) 2 x Cinch socket Audio output (digital) Data interface Standard fi bre-optic cable (SPDIF)/ 1 x Cinch socket Common Interface For 1 CA module USB 1 x 2.0 RS 232 General Information RJ 11 Ambient temperature °C Max. +5 to +40 Unit dimensions (W x H x D)/weight mm/kg 310 x 55 x 210/< 2 115
Page 1 and 2:
Operating manual English UFS 903 si
Page 3 and 4:
List of contents Preface...........
Page 5 and 6:
List of contents Main menu - Servic
Page 7 and 8:
Safety instructions - Important Inf
Page 9 and 10:
Important Information This unit mak
Page 11 and 12:
Features Reception of digital sate
Page 13 and 14:
1. On/Off switch 1) 2. 12 character
Page 15 and 16:
Connection and setup For recording
Page 17 and 18:
Connection and setup Connect the sa
Page 19 and 20:
Use the buttons to select whether
Page 21 and 22:
Number of Satellites When selecting
Page 23 and 24:
Satellite selection When selecting
Page 25 and 26:
Set borders Connection and setup Yo
Page 27 and 28:
Connection and setup Use the butto
Page 29 and 30:
Confi gure satellites Press the bu
Page 31 and 32:
Satellite and Position When selecti
Page 33 and 34:
LNB Type (settings) Use the button
Page 35 and 36:
Transmission channel Use the butto
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
If you do not want to perform a cha
Page 45 and 46:
Local time offset (UTC) Connection
Page 47 and 48:
General operating instructions Afte
Page 49 and 50:
Basic operation in TV or Radio mode
Page 51 and 52:
Page 53 and 54:
Basic operation in TV or radio mode
Page 55 and 56:
Page 57 and 58:
EPG (Electronic Programme Guide) Th
Page 59 and 60:
Page 61 and 62:
Page 63 and 64: The (red dot) button allows you to
Page 65 and 66: Use the buttons to select the “o
Page 67 and 68: the selection fi eld “Start” an
Page 69 and 70: The “Timer list” view can be ca
Page 71 and 72: Editing the channel list Select the
Page 73 and 74: Channels that are deleted from a li
Page 75 and 76: Use the buttons to select “Start
Page 77 and 78: Recording archive (play back/edit r
Page 85 and 86: Main Menu The main menu is opened b
Page 87 and 88: After calling up the menu you will
Page 89 and 90: After calling up the menu you will
Page 91 and 92: Note: You can cancel the search at
Page 93 and 94: Main menu - Channel search Then use
Page 95 and 96: Defi ne new PIN Code Confi rm the s
Page 97 and 98: TV aspect ratio Here you select the
Page 99 and 100: Front display brightness Main menu
Page 101 and 102: You can fi nd out from the “Main
Page 103 and 104: Main menu - Service menu After call
Page 105 and 106: The following display appears (exam
Page 107 and 108: Main menu - Service menu Use the b
Page 109 and 110: Formatting Main menu - Service menu
Page 111 and 112: You can use the buttons to activat
Page 113: You can also download the updates f
Page 117 and 118: Technical appendix ** ) Overvoltage
Page 119 and 120: Technical appendix ** ) Overvoltage
Page 121 and 122: HDCP - High-bandwidth Digital Conte
Page 123 and 124: Service If, despite studying this o
show all

9363637b, Operating manual HDTV Satellite Receiver ... - Kathrein

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?