Cyclo® 6000 - Sumitomo Drive Technologies

All dimensions are in inches
Model
CVF
6160/5DCY
7.8734
7.8723
6170/5DCY
9.8419
9.8408
6180/5DBY 11.0230
11.0217
6190/5DAY 12.5977
12.5963
6190/5DBY 12.5977
12.5963
Cyclo® 6000 Series
CYCLO® 6000 Speed Reducers
Dimensions Vertical F-Flange Mount
Double Reduction
CVF-6160/5DCY 6190/5DBY
*Shaft Tolerances
Shaft Nominal Diameter (inches) Tolerances (inches)
0.500 (1/2) through 0.625 (5/8) +0.0000/-0.0004
0.750 (3/4) through 1.125 (1 1/8) +0.0000/-0.0005
1.250 (1 1/4) through 1.875 (1 7/8) +0.0000/-0.0006
2.000 (2) through 3.125 (3 1/8) +0.0000/-0.0007
3.250 (3 1/4) through 4.625 (4 5/8) +0.0000/-0.0009
4.750 (4 3/4) through 7.000 (7) +0.0000/-0.0010
B C G H NO. M N P Q S1 AH X Y
18.19 0.39 0.55 6 8.74 30 11.81 M12 1.38 10.63 7.72 9.06
20.04 0.47 0.55 8 10.31 22.5 13.39 M12 1.61 11.81 8.58 10.24
22.72 0.47 0.55 8 11.77 22.5 14.57 M12 1.50 12.99 9.17 10.24
24.76 0.39 0.55 12 14.37 15 16.93 M12 1.61 14.96 10.04 10.24
25.71 0.39 0.55 12 14.37 15 16.93 M12 1.61 14.96 10.04 10.24
Model Low Speed Shaft High Speed Shaft Approx.
CVF U* V S L1 Key XU* XV Key Wt. (lb.)
6160/5DCY 2.250 3.15 3/8-16UNC 0.71 1/2 X 1/2 X 2.95 0.750 1.38 3/16 X 3/16 X1.02 181
6170/5DCY 2.750 3.31 1/2-13UNC 0.94 5/8 X 5/8 X 3.15 0.750 1.38 3/16 X 3/16 X1.02 232
6180/5DBY 3.125 3.94 1/2-13UNC 0.94 3/4 X 3/4 X 3.74 0.875 1.57 3/16 X 3/16 X1.38 322
6190/5DAY 3.625 4.92 3/4-10UNC 1.34 7/8 X 7/8 X 4.92 0.750 1.38 3/16 X 3/16 X1.02 443
6190/5DBY 3.625 4.92 3/4-10UNC 1.34 7/8 X 7/8 X 4.92 0.875 1.57 3/16 X 3/16 X1.38 452
Dimensions shown are for reference only and are subject to change without notice, unless certified.
Certified prints are available after receipt of an order; consult factory.
Dimensions
Dimensions 4.53
Speed
Reducers