Cyclo® 6000 - Sumitomo Drive Technologies
Cyclo® 6000 - Sumitomo Drive Technologies
Cyclo® 6000 - Sumitomo Drive Technologies
Create successful ePaper yourself
Turn your PDF publications into a flip-book with our unique Google optimized e-Paper software.
Speed<br />
Reducers<br />
Dimensions<br />
CYCLO® <strong>6000</strong> Speed Reducers<br />
Dimensions Foot Mount, Hollow Input<br />
Double Reduction<br />
CNHX-6065DAY 6140/5DCY<br />
All dimensions are in inches<br />
Model Low Speed Shaft<br />
CNHX U* V S L1 Key<br />
6065DAY 0.500 0.98 10-32UNF 0.63 1/8 X 1/8 X .79<br />
6075DAY 0.750 1.18 12-28UNF 0.63 3/16 X 3/16 X 1.06<br />
6095DAY 1.125 1.38 5/16-18UNC 0.79 1/4 X 1/4 X 1.18<br />
6105DAY 1.125 1.38 5/16-18UNC 0.79 1/4 X 1/4 X 1.18<br />
6125DBY 1.500 2.17 5/16-18UNC 0.79 3/8 X 3/8 X 1.77<br />
6130/5DAY 1.875 2.76 3/8-16UNC 0.71 1/2 X 1/2 X 2.16<br />
6130/5DBY 1.875 2.76 3/8-16UNC 0.71 1/2 X 1/2 X 2.16<br />
6130/5DCY 1.875 2.76 3/8-16UNC 0.71 1/2 X 1/2 X 2.16<br />
6140/5DAY 1.875 3.54 3/8-16UNC 0.71 1/2 X 1/2 X 2.95<br />
6140/5DBY 1.875 3.54 3/8-16UNC 0.71 1/2 X 1/2 X 2.95<br />
6140/5DCY 1.875 3.54 3/8-16UNC 0.71 1/2 X 1/2 X 2.95<br />
4.30 Dimensions<br />
Dimensions shown are for reference only and are subject to change without notice, unless certified.<br />
Certified prints are available after receipt of an order; consult factory.<br />
*Shaft Tolerances<br />
Shaft Nominal Diameter (inches) Tolerances (inches)<br />
0.500 (1/2) through 0.625 (5/8) +0.0000/-0.0004<br />
0.750 (3/4) through 1.125 (1 1/8) +0.0000/-0.0005<br />
1.250 (1 1/4) through 1.875 (1 7/8) +0.0000/-0.0006<br />
Model<br />
CNHX<br />
A B L D E E1 F F1 G H J O P BW<br />
6065DAY 5.67 3.31 4.92 3.150 2.36 0.47 2.36 0.47 0.39 0.35 1.38 5.31 4.33 1.61<br />
6075DAY 5.67 3.31 5.16 3.150 2.36 0.47 2.36 0.47 0.39 0.35 1.38 5.31 4.33 1.85<br />
6095DAY 7.09 5.31 7.48 3.937 2.95 0.59 3.54 0.59 0.47 0.43 1.57 6.89 5.91 2.36<br />
6105DAY 7.09 5.31 8.03 3.937 2.95 0.59 3.54 0.59 0.47 0.43 1.57 6.89 5.91 2.36<br />
6125DBY 9.06 6.10 9.92 4.724 3.74 0.79 4.53 0.79 0.59 0.55 2.17 8.74 8.03 3.23<br />
6130/5DAY 12.99 7.68 11.58 5.906 5.71 0.79 5.71 0.98 0.87 0.71 2.56 11.81 9.06 3.94<br />
6130/5DBY 12.99 7.68 11.94 5.906 5.71 0.79 5.71 0.98 0.87 0.71 2.56 11.81 9.06 3.94<br />
6130/5DCY 12.99 7.68 12.48 5.906 5.71 0.79 5.71 0.98 0.87 0.71 2.56 11.81 9.06 3.94<br />
6140/5DAY 12.99 7.68 12.36 5.906 5.71 0.79 5.71 0.98 0.87 0.71 2.56 11.81 9.06 4.72<br />
6140/5DBY 12.99 7.68 12.72 5.906 5.71 0.79 5.71 0.98 0.87 0.71 2.56 11.81 9.06 4.72<br />
6140/5DCY 12.99 7.68 13.26 5.906 5.71 0.79 5.71 0.98 0.87 0.71 2.56 11.81 9.06 4.72<br />
Note: [1] Center height “D” for 6065DAY and 6075DAY is less than the radius of motor flange diameter half of “BD” (frame 56C).<br />
<strong>Cyclo®</strong> <strong>6000</strong> Series
Change language