Cyclo® 6000 - Sumitomo Drive Technologies

All dimensions are in inches
Model
CHF
6130/5Y
6.4955
6.4945
6140/5Y
6.4955
6.4945
6160/5Y
7.8734
7.8723
6170/5Y
9.8419
9.8408
6180/5Y 11.0230
11.0217
6190/5Y 12.5977
12.5963
CYCLO® 6000 Speed Reducers
Dimensions Horizontal F-Flange Mount
Cyclo® 6000 Series
Single Reduction
CHF-6130/5 6190/5Y
*Shaft Tolerances
Shaft Nominal Diameter (inches) Tolerances (inches)
0.500 (1/2) through 0.625 (5/8) +0.0000/-0.0004
0.750 (3/4) through 1.125 (1 1/8) +0.0000/-0.0005
1.250 (1 1/4) through 1.875 (1 7/8) +0.0000/-0.0006
2.000 (2) through 3.125 (3 1/8) +0.0000/-0.0007
3.250 (3 1/4) through 4.625 (4 5/8) +0.0000/-0.0009
4.750 (4 3/4) through 7.000 (7) +0.0000/-0.0010
B C G H NO. M N P P1 Q S1 AH X
12.64 0.63 0.43 6 7.01 60 9.06 9.06 M10 1.22 8.07 8.19
13.43 0.63 0.43 6 7.80 60 9.06 9.06 M10 1.22 8.07 8.19
16.26 0.39 0.55 6 8.74 30 11.81 12.52 M12 1.38 10.63 8.98
18.78 0.47 0.55 8 10.31 22.5 13.39 14.25 M12 1.61 11.81 9.57
20.75 0.47 0.55 8 11.77 22.5 14.57 15.35 M12 1.50 12.99 10.16
24.41 0.39 0.55 12 14.37 15 16.93 17.76 M12 1.61 14.96 11.22
Model Low Speed Shaft High Speed Shaft Approx.
CHF U* V S L1 Key XU* XV Key Wt. (lb.)
6130/5Y 1.875 2.76 3/8-16UNC 0.71 1/2 X 1/2 X 2.16 0.875 1.57 3/16 X 3/16 X 1.38 79
6140/5Y 1.875 3.54 3/8-16UNC 0.71 1/2 X 1/2 X 2.95 0.875 1.57 3/16 X 3/16 X 1.38 82
6160/5Y 2.250 3.54 3/8-16UNC 0.71 1/2 X 1/2 X 2.95 1.125 1.77 1/4 X 1/4 X 1.77 146
6170/5Y 2.750 3.54 1/2-13UNC 0.94 5/8 X 5/8 X 3.15 1.375 2.17 5/16 X 5/16 X 2.16 212
6180/5Y 3.125 4.33 1/2-13UNC 0.94 3/4 X 3/4 X 3.74 1.500 2.56 3/8 X 3/8 X 2.56 289
6190/5Y 3.625 5.31 3/4-10UNC 1.34 7/8 X 7/8 X 4.92 1.750 2.76 3/8 X 3/8 X 2.76 430
Dimensions shown are for reference only and are subject to change without notice, unless certified.
Certified prints are available after receipt of an order; consult factory.
Dimensions
Dimensions 4.37
Speed
Reducers