Cyclo® 6000 - Sumitomo Drive Technologies

More documents

Recommendations

Info

CYCLO® 6000 Speed Reducers Standard Specifications Reducer Reduction: Internal planetary gear mechanism with trochoidal curved tooth profile. Shaft Rotation On single reduction Cyclo® speed reducers, ratios 3 through 119, the slow speed shaft rotates in a reverse direction to that of the high speed shaft. On double reduction units, ratios 104 through 7569, both the high speed and the slow speed shaft rotate in the same direction. Input Speeds In general terms, the standard input speeds of single reduction units are 1750, 1165, 875, 580, and 50 RPM. When non-standard input speeds are used, the horsepower and torque ratings will also vary. Thermal Capacity The Cyclo® speed reducer’s smooth, almost frictionless operation all but eliminates the conventional limitations due to heat. In all sizes, Cyclo® speed reducers have thermal ratings that exceed their mechanical capacity. 1.6 General Information Lubrication: Grease or oil lubricated models available. Seals: Nitrile material, dual lipped, double output seals available. Material: Rugged cast iron or ductile housings. Paint Color: Blue, Munsell color number 6.5PB 3.6/8.2 Ambient Installation Location: Indoors (Minimal dust and humidity) Conditions Ambient Temperature: 14°~104° F (-10º ~ 40º C) Ambient Humidity: Under 85% Elevation: Under 3,281 ft. (1000 meters) Atmosphere: Well ventilated location, free of corrosive gases, explosive gases, vapors and dust. Cyclo® 6000 Series
Cyclo® 6000 Series CYCLO® 6000 Speed Reducers 2 How to Select How to Select 2.1 How to Select
Page 1 and 2: WoRlDWIDE loCATIoNS Sumitomo Machin
Page 3 and 4: Cyclo® 6000 boasts an expanded ran
Page 5 and 6: Product Description Sumitomo Cyclo
Page 7: How do I select a Cyclo® speed red
Page 11 and 12: The Service Factor table below pres
Page 13 and 14: Cyclo® 6000 Series CYCLO® 6000 Sp
Page 15 and 16: Reducer Specification Nominal Total
Page 17 and 18: Cyclo® 6000 Series 3 Selection Tab
Page 19 and 20: Dimensions: Pages Foot Mount (H) 4.
Page 39 and 40: Cyclo® 6000 Series CYCLO® 6000 Sp
Page 41 and 42: NOTE: Motor HP in GRAY is to overco
Page 53 and 54: Cyclo® 6000 Series 4 Dimensions Sp
Page 55 and 56: All dimensions are in inches Model
Page 57 and 58: All dimensions are in inches Model
Page 59 and 60:
All dimensions are in inches Model
Page 61 and 62:
Cyclo® 6000 Series This page inten
Page 63 and 64:
All dimensions are in inches Cyclo
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78:
Page 79 and 80:
Page 81 and 82:
Page 83 and 84:
Page 85 and 86:
Page 87 and 88:
Page 89 and 90:
Page 91 and 92:
Page 93 and 94:
Page 95 and 96:
All dimensions are in inches CYCLO
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
Page 105 and 106:
Page 107 and 108:
Page 109 and 110:
Page 111 and 112:
Cyclo® 6000 Series CYCLO® 6000 Sp
Page 113 and 114:
Page 115 and 116:
Page 117 and 118:
Page 119 and 120:
Page 121 and 122:
Page 123 and 124:
Page 125 and 126:
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
Page 135 and 136:
Page 137 and 138:
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
HORIZONTAL Mounted Reducer • SING
Page 155 and 156:
Oil Fill Quantities Single Reductio
Page 157 and 158:
Load Location Factors (Lf), Slow Sp
Page 159 and 160:
Ductile Iron Housing and High Capac
Page 161 and 162:
Load Location Factors (Lf), High Sp
Page 163 and 164:
How to Calculate Axial Loads When a
Page 165 and 166:
show all

Cyclo® 6000 - Sumitomo Drive Technologies

Create successful ePaper yourself

Delete template?

Save as template?