Cyclo® 6000 - Sumitomo Drive Technologies

All dimensions are in inches
Cyclo® 6000 Series
CYCLO® 6000 Speed Reducers
Dimensions Vertical and Universal V-Flange Mount, Shovel Base
Model
CNV A B C G H NO. M P AH
CVV [1]
6120/5Y-SB 8.27
6130/5Y-SB 10.24
6140/5Y-SB 10.24
5.5101
5.5076
7.8720
7.8692
7.8720
7.8692
10.20 0.51 0.43 6 2.72 0.16 7.09
12.64 0.59 0.43 6 2.99 0.16 9.06
13.43 0.59 0.43 6 3.78 0.16 9.06
Single Reduction
CNV [1] -6120/5Y-SB
CVV [1] -6130/5Y 6140/5Y-SB
*Shaft Tolerances
Shaft Nominal Diameter (inches) Tolerances (inches)
0.500 (1/2) through 0.625 (5/8) +0.0000/-0.0004
0.750 (3/4) through 1.125 (1 1/8) +0.0000/-0.0005
1.250 (1 1/4) through 1.875 (1 7/8) +0.0000/-0.0006
2.000 (2) through 3.125 (3 1/8) +0.0000/-0.0007
3.250 (3 1/4) through 4.625 (4 5/8) +0.0000/-0.0009
4.750 (4 3/4) through 7.000 (7) +0.0000/-0.0010
Model Low Speed Shaft High Speed Shaft
CNV
CVV [1] U* V S L1 Key XU* XV Key
6120/5Y-SB 1.500 2.17 5/16-18UNC 0.79 3/8 X 3/8 X 1.77 0.750 1.38 3/16 X 3/16 X 1.02
6130/5Y-SB 1.875 2.40 3/8-16UNC 0.71 1/2 X 1/2 X 2.16 0.875 1.57 3/16 X 3/16 X 1.38
6140/5Y-SB 1.875 3.19 3/8-16UNC 0.71 1/2 X 1/2 X 2.95 0.875 1.57 3/16 X 3/16 X 1.38
Model
CNV, CVV
Dimensions 143T 145T 182T 184T 213T 215T 254T 256T 284T 286T 324T 326T 364T 365T
[1]
C2 24.25 24.25 28.74
6120/5Y-SB GAP 0.50 0.52 0.71 0.88
WT W/O MOTOR 83 81 96
C2 30.83 30.83 30.83 34.84
6130/5Y-SB GAP 0.50 0.52 0.71 0.88 1.00
WT W/O MOTOR 125 125 135 135
C2 31.61 31.61 31.61 35.63
6140/5Y-SB GAP 0.50 0.52 0.71 0.88 1.00
WT W/O MOTOR 171 146 143 154
Note: [1] Model 6120/5Y-SB is type CNV; Models 6130/5Y-SB and 6140/5Y-SB are type CVV.
Dimensions shown are for reference only and are subject to change without notice, unless certified.
Certified prints are available after receipt of an order; consult factory.
Dimensions
Dimensions 4.75
Speed
Reducers