Cyclo® 6000 - Sumitomo Drive Technologies

More documents

Recommendations

Info

Speed Reducers Dimensions CYCLO® 6000 Speed Reducers 4.20 Dimensions This page intentionally left blank. Dimensions shown are for reference only and are subject to change without notice, unless certified. Certified prints are available after receipt of an order; consult factory. Cyclo® 6000 Series
All dimensions are in inches Model CNH CYCLO® 6000 Speed Reducers Dimensions Foot Mount Double Reduction CNH-6060/5DAY 6120/5DBY *Shaft Tolerances Shaft Nominal Diameter (inches) Tolerances (inches) 0.500 (1/2) through 0.625 (5/8) +0.0000/-0.0004 0.750 (3/4) through 1.125 (1 1/8) +0.0000/-0.0005 1.250 (1 1/4) through 1.875 (1 7/8) +0.0000/-0.0006 2.000 (2) through 3.125 (3 1/8) +0.0000/-0.0007 3.250 (3 1/4) through 4.625 (4 5/8) +0.0000/-0.0009 4.750 (4 3/4) through 7.000 (7) +0.0000/-0.0010 A B C D E E1 F F1 G H J O1 O P BW 6060/5DAY 5.67 3.31 7.01 3.150 2.36 0.47 2.36 0.47 0.39 0.35 1.38 5.31 - 4.33 1.61 6070/5DAY 5.67 3.31 7.24 3.150 2.36 0.47 2.36 0.47 0.39 0.35 1.38 5.31 - 4.33 1.85 6090/5DAY 7.09 5.31 9.57 3.937 2.95 0.59 3.54 0.59 0.47 0.43 1.57 6.89 - 5.91 2.36 6100/5DAY 7.09 5.31 10.12 3.937 2.95 0.59 3.54 0.59 0.47 0.43 1.57 - 8.15 5.91 2.36 6120/5DBY 9.06 6.10 12.28 4.724 3.74 0.79 4.53 0.79 0.59 0.55 2.17 - 10.12 8.03 3.23 Model Low Speed Shaft High Speed Shaft Approx. CNH U* V S L1 Key XU* XV Key Wt. (lb.) 6060/5DAY 0.500 0.98 10-32UNF 0.63 1/8 X 1/8 X .79 0.500 0.98 1/8 X 1/8 X 0.71 9 6070/5DAY 0.750 1.18 12-28UNF 0.63 3/16 X 3/16 X 1.06 0.500 0.98 1/8 X 1/8 X 0.71 10 6090/5DAY 1.125 1.38 5/16-18UNC 0.79 1/4 X 1/4 X 1.18 0.500 0.98 1/8 X 1/8 X 0.71 26 6100/5DAY 1.125 1.38 5/16-18UNC 0.79 1/4 X 1/4 X 1.18 0.500 0.98 1/8 X 1/8 X 0.71 33 6120/5DBY 1.500 2.17 5/16-18UNC 0.79 3/8 X 3/8 X 1.77 0.625 0.98 3/16 X 3/16 X 0.75 64 Cyclo® 6000 Series Dimensions shown are for reference only and are subject to change without notice, unless certified. Certified prints are available after receipt of an order; consult factory. Dimensions Dimensions 4.21 Speed Reducers
Page 1 and 2:
WoRlDWIDE loCATIoNS Sumitomo Machin
Page 3 and 4:
Cyclo® 6000 boasts an expanded ran
Page 5 and 6:
Product Description Sumitomo Cyclo
Page 7 and 8:
How do I select a Cyclo® speed red
Page 9 and 10:
Cyclo® 6000 Series CYCLO® 6000 Sp
Page 11 and 12:
The Service Factor table below pres
Page 13 and 14:
Page 15 and 16:
Reducer Specification Nominal Total
Page 17 and 18:
Cyclo® 6000 Series 3 Selection Tab
Page 19 and 20:
Dimensions: Pages Foot Mount (H) 4.
Page 21 and 22: Dimensions: Pages Foot Mount (H) 4.
Page 39 and 40: Cyclo® 6000 Series CYCLO® 6000 Sp
Page 41 and 42: NOTE: Motor HP in GRAY is to overco
Page 53 and 54: Cyclo® 6000 Series 4 Dimensions Sp
Page 55 and 56: All dimensions are in inches Model
Page 61 and 62: Cyclo® 6000 Series This page inten
Page 63 and 64: All dimensions are in inches Cyclo
Page 71: All dimensions are in inches Cyclo
Page 95 and 96: All dimensions are in inches CYCLO
Page 103 and 104: Cyclo® 6000 Series This page inten
Page 111 and 112: Cyclo® 6000 Series CYCLO® 6000 Sp
Page 123 and 124:
All dimensions are in inches CYCLO
Page 125 and 126:
All dimensions are in inches Cyclo
Page 127 and 128:
Page 129 and 130:
Page 131 and 132:
Page 133 and 134:
All dimensions are in inches Model
Page 135 and 136:
All dimensions are in inches Model
Page 137 and 138:
Cyclo® 6000 Series This page inten
Page 139 and 140:
Page 141 and 142:
Page 143 and 144:
Page 145 and 146:
Page 147 and 148:
Page 149 and 150:
Page 151 and 152:
Page 153 and 154:
HORIZONTAL Mounted Reducer • SING
Page 155 and 156:
Oil Fill Quantities Single Reductio
Page 157 and 158:
Load Location Factors (Lf), Slow Sp
Page 159 and 160:
Ductile Iron Housing and High Capac
Page 161 and 162:
Load Location Factors (Lf), High Sp
Page 163 and 164:
How to Calculate Axial Loads When a
Page 165 and 166:
show all

Cyclo® 6000 - Sumitomo Drive Technologies

Create successful ePaper yourself

Delete template?

Save as template?