Renesas MCU M16C Family (R32C/M32C/M16C/R8C) - Glyn
Renesas MCU M16C Family (R32C/M32C/M16C/R8C) - Glyn
Renesas MCU M16C Family (R32C/M32C/M16C/R8C) - Glyn
You also want an ePaper? Increase the reach of your titles
YUMPU automatically turns print PDFs into web optimized ePapers that Google loves.
AN27<br />
AN20<br />
AN07<br />
AN00<br />
AN7<br />
AN0<br />
AN EX1<br />
AN EX0<br />
Vcc<br />
GND<br />
Vcc<br />
GND<br />
A/D Converter<br />
High-Speed A/D Converter with Sample-and-Hold Vref Cutoff<br />
(1) Conversion Speed (ØAD = 10MHz)<br />
10-Bit: 3.3 µs<br />
8-Bit: 2.8 µs<br />
(2) Successive Conversion ±3 LSB Accuracy<br />
(3) High-Speed Sample-and-Hold<br />
10MHz Operation: 0.3 µs, 20MHz Operation: 0.15 µs (Target)<br />
TB2<br />
AN0(TB0)<br />
One-Shot Pulse<br />
AN1(TB1)<br />
One-Shot Pulse<br />
S/H<br />
A/D Converter<br />
Max. 26-Channel A/D Pins (<strong>M16C</strong>/62P)<br />
(<strong>M32C</strong>/64: Max. 34-Channel)<br />
(<strong>M16C</strong>/30P: Max. 10-Channel)<br />
(<strong>M16C</strong>/28: Max. 24-Channel)<br />
A/D Converter<br />
The analog circuit reference voltage, Vref, can be turned on or off.<br />
Turning off Vref when the A/D converter is not being used can<br />
help reduce current consumption.<br />
TB2<br />
Vref<br />
AVss<br />
Analog Input<br />
A/D Conversion Function with AN0 and AN1 Delay Triggers<br />
TB0 and TB1 One-Shot Operation Start<br />
A/D Conversion Timing<br />
TB0 and TB1 one-shot mode starts with TB2 underflow as the<br />
trigger. The TB0 and TB1 one-shot pulses act as the triggers<br />
for prioritized AN0 and AN1 A/D conversion with<br />
sample-and-hold.<br />
Measurement Error Avoidance (Unused A/D Overvoltage Processing)<br />
This feature helps prevent measurement error due to<br />
wraparound between channels, even if the other A/D<br />
inputs include input that exceeds the Vcc level. It also<br />
provides more accurate A/D conversion values.<br />
OFF<br />
ON<br />
S/H Trigger<br />
TB0<br />
One-Shot Mode<br />
Resistor<br />
S/H<br />
S/H Trigger<br />
TB1 S/H<br />
A/D Converter<br />
(2) Underflow of TB0 and TB1 are added as<br />
AN0 and AN1 A/D conversion triggers.<br />
Underflow Signal<br />
Trigger<br />
Trigger<br />
One-Shot Mode<br />
(1) One-shot mode is added for<br />
TB0 and TB1.<br />
(One trigger is output per cycle.)<br />
Note: There are no dedicated A/D trigger<br />
output pins.<br />
A/D Converter<br />
(ANO)<br />
(AN1)<br />
A/D<br />
(4) Part of A/D conversion<br />
sequence changed.<br />
(3) Sample-and-hold added exclusively to AN1.<br />
(Supports two A/D conversion requests in a short time.)<br />
16