Drawings - Peak Engineering and Construction Ltd

Recommendations

Info

A B C D EXISTING 200 SST PIPE GENERATOR ROOM TEMPORARILY DISCONNECT EXISTING FLUOSILICIC ACID TRANSFER TUBE/PIPE FROM EXISTING 350 SST DISCHARGE HEADER. REFER TO PHOTOGRAPH 2 FOR RECONNECTION EXISTING 350 GATE VALVE TO REMAIN REUSE EXISTING PIPE SUPPORT 1 2 3 4 5 6 1 DETAIL NTS 000-D-2001 REMOVE EXISTING VENTURI TRANSMITTER, PIPE BRACKET SUPPORT, AND CONCRETE BASE. REFER TO DETAIL 0330-143 ON STRUCTURAL DRAWINGS FOR CONCRETE BASE REMOVAL EXISTING SILO REMOVE EXISTING 200 KNIFE GATE VALVE. REPLACE WITH 200 ROTARY VALVE. SHORTEN EXISTING 200 SST PIPE TO SUIT. REUSE EXISTING EXPANSION JOINTS EXISTING EXPANSION JOINTS SODA ASH ROOM REMOVE EXISTING SECTION OF 40-CLS-PVC PIPING CONNECTED TO EXISTING 350 SST DISCHARGE HEADER. PROVIDE 40 NPT SST PLUG ON NEW SECTION OF 350 SST DISCHARGE HEADER REFER TO PHOTOGRAPH 2 FOR RECONNECTION. SST BYPASS COUPLING VENTURI METER AS SHOWN EXISTING 40-CLS-PVC EXISTING 350 REUSE EXISTING 350 VICTAULIC REMOVE EXISTING SECTION OF 350 SST DISCHARGE HEADER AND GENERATOR ROOM RECONNECT EXISTING 2 DETAIL NTS 000-D-2002 FLUOSILICIC ACID TRANSFER TUBE/PIPE SUPPLY TO NEW SECTION OF 350 SST DISCHARGE HEADER. PROVIDE 25 NPT SST HALF COUPLING ON 350 SST DISCHARGE HEADER REFER TO NOTE 2 REUSE EXISTING PIPE SUPPORT 4 DETAIL NTS 000-D-2001 350 SST DISCHARGE HEADER REFER TO DWG 000-M-1001 FOR REMOVAL OF EXISTING SILO FILTER DUCT. DUCT NOT REQUIRED FOR NEW SILO FILTER SODA ASH ROOM REMOVE EXISTING SILO FILTER AND REPLACE WITH NEW SILO FILTER EXISTING FLANGE TO REMAIN ON TOP OF EXISTING SILO. FABRICATE CARBON STEEL TRANSITION TO CONNECT NEW SILO FILTER TO EXISTING 1050x1050 FLANGE ON TOP OF SILO. CONTRACTOR TO VERIFY FLANGE SIZE AND BOLT PATTERN. REFER TO SECTION 11254 TOP OF EXISTING SILO EXTEND EXISTING 40-CLS-PVC PIPE TO WALL SIDE EXISTING 40-CLS-PVC OF 350 SST DISCHARGE HEADER. PROVIDE SST NPT COUPLING ON 350 SST DISCHARGE HEADER. PROVIDE BALL VALVE ON CHLORINE PIPE AT 350 SST DISCHARGE HEADER EXISTING WALL DEMOLITION (PHOTOGRAPH 1) NEW PIPING (PHOTOGRAPH 2) NEW PIPING (PHOTOGRAPH 3) EXISTING 350 SST BYPASS EXISTING 350 VICTAULIC COUPLING 350 MAGNETIC FLOW METER FE-5001 REFER TO PHOTOGRAPH 3 FOR CONTINUATION EXISTING PIPE SUPPORT REFER TO PHOTOGRAPH 2 FOR CONTINUATION PROVIDE 40 NPT SST PLUG FOR EXISTING COUPLING ON 350 SST DISCHARGE HEADER GENERATOR ROOM REMOVE SECTION OF EXISTING 25 SST PIPE IN VERTICAL TO SUIT CONNECTION OF 2 25-EDW-SST PIPES EXISTING 350 SST DISCHARGE HEADER NOTES: 25 BACKFLOW 25 GLOBE VALVE 25 CHECK VALVE PREVENTER RECIRCULATION PUMP PHOTOGRAPH 4 3 DETAIL NTS 000-D-2001 GENERATOR ROOM FLOW 25 BALL VALVE VALVE EXISTING 350 SST BYPASS 6-SHX-PE FOR CONTINUATION CHEMICAL 5 INJECTOR 000-D-5001 REFER TO NOTE 2 THEMSELVES WITH THE SCOPE OF WORK PRIOR TO PROCEEDING. SOME PIPING AND EQUIPMENT HAS BEEN OMITTED FOR CLARITY. STAINLESS STEEL PIPING WHERE REQUIRED BEFORE INSULATING. 25-EDW-SST 25 BALL VALVE CONNECT 25-EDW-SST TO EXISTING 25 SST PIPE BETWEEN EXISTING TEE AND EXISTING BALL REFER TO DWG 000-D-2001 000-D-5002 DATE PROJ SHEET VERIFY SCALE FILENAME: 000-D-2006_424251.dgn PLOT DATE: 2012\07\25 PLOT TIME: 5:49:46 PM 2 PROVIDE 25 SST NPT HALF COUPLING ON EXISTING 350 SST DISCHARGE HEADER 1. CONTRACTOR TO VERIFY ALL EXISTING CONDITIONS TO FAMILIARIZE 2. PROVIDE REMOVABLE INSULATION SECURED WITH VELCRO ADHESIVE AROUND VALVES, EQUIPMENT (EXCLUDING PUMPS AND AIR/VACUUM RELIEF VALVES), INJECTION POINTS ETC. PER SECTION 15080 FOR ENTIRE LENGTH OF PUMP DISCHARGE HEADER AND BYPASS IN GENERATOR ROOM. CLEAN AND PASSIVATE DISTRICT M UNICIPALITY DWG OF M USKOKA FAIRYVIEW W ATER TREATMENT PLANT PROCESS MECHANICAL MB JPN ISSUED FOR TENDER 07/2012 0 PHASE I UPGRADES BAR IS 25mm ON APVD BY REVISION DATE NO. CONTRACT 12-432-253 PIPING MODIFICATIONS (1) ORIGINAL DRAWING. 0 25 MM APVD CHK DSGN DR 13of62 ET JPN JPN RC 2012/07/27 424251 000-D-2006 CH2M HILL 2012. ALL RIGHTS RESERVED. c THIS DOCUMENT, AND THE IDEAS AND DESIGNS INCORPORATED HEREIN, AS AN INSTRUMENT OF PROFESSIONAL SERVICE, IS THE PROPERTY OF CH2M HILL AND IS NOT TO BE USED, IN W HOLE OR IN PART, FOR ANY OTHER PROJECT WITHOUT THE W RITTEN AUTHORIZATION OF CH2MHILL. REUSE OF DOCUMENTS: ISSUED FOR TENDER
A B C D 1 2 3 4 5 6 FLOC TANK No. 3 FLOC TANK No. 1 RAPID MIXING CHAMBER CHEMICAL PIPING DEMOLITION 1:50 CHAMBER REMOVE EXISTING 65 PVC POLYELECTROLYTES PIPE EXCEPT FOR PORTION IN SODA ASH RETENTION CHAMBER SODA ASH RETENTION CHAMBER JANITOR ROOM EXISTING 40 PVC CHLORINE CHEMICAL STORAGE EXISTING WALL BETWEEN SODA ASH RETENTION CHAMBER AND JANITOR ROOM. PROVIDE PVC CAP ON PIPE ON JANITOR ROOM SIDE OF WALL ONLY. FILL PIPE COMPLETELY WITH GROUT FLUSH WITH SODA ASH RETENTION CHAMBER WALL REMOVE EXISTING 65 PVC SODIUM CARBONATE PIPE EXCEPT FOR PORTION IN EXISTING WALL BETWEEN SODA ASH RETENTION CHAMBER AND JANITOR ROOM. PROVIDE PVC CAP ON PIPE ON JANITOR ROOM SIDE OF WALL ONLY. FILL PIPE COMPLETELY WITH GROUT FLUSH WITH SODA ASH RETENTION CHAMBER WALL EXISTING CONCRETE BLOCK WALL COVERING CONCRETE TANK WALL BETWEEN SODA ASH RETENTION CHAMBER AND JANITOR ROOM 1 PHOTO 2 PHOTO SODA ASH MIXING CHAMBER REMOVE EXISTING 65 PVC SODIUM CARBONATE PIPING REMOVE EXISTING 65 PVC PHOTOGRAPH (JANITOR ROOM) 1 NTS PROVIDE PVC CAP ON PIPE ON ONE SIDE OF EACH WALL ONLY. CUT PIPE FLUSH WITH OTHER SIDE OF WALL WHEN REMOVING PIPE SECTIONS. FILL PIPE WITHIN WALL COMPLETELY WITH NON-SHRINK, NON-FERROUS GROUT FLUSH WITH OTHER SIDE OF WALL. REFER TO DETAIL ON THIS DRAWING FOR NEW CHEMICAL PIPING. ALL REPAIRS TO BE WATER TIGHT POLYELECTROLYTES PIPING EXISTING 20 PVC ALUMINUM SULPHATE EXISTING 40 PVC CHLORINE EXISTING CONCRETE TANK WALL EXISTING CONCRETE BLOCK WALL EXISTING 65 PVC POLYELECTROLYTES PIPING TERMINATES AT THIS POINT REMOVE EXISTING 65 PVC SODIUM CARBONATE PIPE BACK TO SODA ASH ROOM EXISTING 20 PVC ALUMINUM SULPHATE EXISTING 40 PVC CHLORINE EXISTING 40 PVC CHLORINE EXISTING 20 PVC ALUMINUM SULPHATE REFER TO PHOTOGRAPH 2 FOR CONTINUATION AND PIPE DEMOLITION DETAILS THROUGH THIS WALL EXISTING CONCRETE BLOCK WALL 1 DETAIL NTS 000-D-2001 EXISTING CONCRETE TANK WALL EXISTING CONCRETE BLOCK WALL EXISTING 20 PVC ALUMINUM SULPHATE REFER TO PHOTOGRAPH 1 FOR CONTINUATION REMOVE EXISTING 65 PVC POLYELECTROLYTES PIPE AND 65 PVC SODIUM CARBONATE PIPE ON BOTH SIDES OF WALL SEPARATING JANITOR ROOM AND CHEMICAL STORAGE AS SHOWN. CUT PIPES FLUSH WITH WALL ON BOTH SIDES OF WALL. PIPES TO REMAIN IN WALL AND WILL BE USED AS SLEEVES FOR 2 NEW 40-LS-PVC PIPES. REFER TO "NEW CHEMICAL PIPING" ON THIS DRAWING FOR ADDITIONAL DETAILS EXISTING CONCRETE BLOCK WALL BETWEEN JANITOR ROOM AND CHEMICAL STORAGE 2 NTS FLOC TANK No. 3 FLOC TANK No. 1 1:50 CHAMBER SODA ASH RETENTION CHAMBER FL EL 293.450 RAPID MIXING CHAMBER SODA ASH RETENTION CHAMBER FL EL 293.450 JANITOR ROOM CHEMICAL STORAGE FOR CONTINUATION 1 PHOTO 2 PHOTO 50-CDS-PVC PIPES FROM CO2 PANEL. REFER TO DWG 000-D-2001 TOC EL 297.850 NEW CHEMICAL PIPING PHOTOGRAPH (CHEMICAL STORAGE) 2 000-D-5001 REMOVE EXISTING 65 PVC SODIUM CARBONATE PIPE BACK TO SODA ASH ROOM. RUN 2 NEW 40-LS-PVC PIPES IN EXISTING PIPE TRAY ALONG SAME ROUTE AS REMOVED SODIUM CARBONATE PIPE NOTES: 50-CDS-PVC RETENTION CHAMBER SODA ASH MIXING CHAMBER EXISTING 20 PVC ALUMINUM SULPHATE EXISTING 40 PVC CHLORINE EXISTING 20 PVC ALUMINUM SULPHATE DIMENSIONS ARE APPROXIMATE. TERMINATE VERTICAL PIPE 500 ABOVE BOTTOM OF SODA ASH 4 000-D-5001 FL EL 293.450 PROVIDE 40 NPT PVC TEE WITH PLUG. TERMINATE VERTICAL PIPE 1000 ABOVE SODA ASH MIXING CHAMBER FLOOR 4 000-D-5001 50-CDS-PVC TERMINATE VERTICAL PIPE 500 ABOVE BOTTOM OF SODA ASH RETENTION CHAMBER 40-LS-PVC 4 000-D-5001 2 REUSE EXISTING PIPE SLEEVES FROM SODIUM CARBONATE AND POLYELECTROLYTE 000-D-5001PIPE REMOVAL DONE UNDER DEMOLITION ON THIS DRAWING 40-LS-PVC FROM LIME ROOM (2 PIPES). RUN PIPES IN EXISTING PIPE TRAY ALONG SAME ROUTE AS REMOVED SODIUM CARBONATE PIPE. REFER TO DWG 000-D-2001 FOR CONTINUATION EXISTING 40 PVC CHLORINE 1. CONTRACTOR TO VERIFY ALL EXISTING CONDITIONS TO FAMILIARIZE THEMSELVES WITH THE SCOPE OF WORK PRIOR TO PROCEEDING. SOME PIPING AND EQUIPMENT HAS BEEN OMITTED, FOR CLARITY. 2. EXISTING BACKGROUND TAKEN FROM TOTTEN SIMS HUBICKI ASSOCIATES IN ASSOCIATION WITH RYSCO ENGINEERING CORPORATION. PROJECT 52-6630, DRAWING M3, AS CONSTRUCTED SEPT. 91. EXISTING BACKGROUND HAS BEEN MODIFIED BY CH2M HILL TO SUIT THIS PROJECT. ALL BACKGROUND DATE PROJ SHEET VERIFY SCALE FILENAME: 000-D-2007_424251.dgn PLOT DATE: 2012\07\26 PLOT TIME: 8:25:55 AM DISTRICT M UNICIPALITY DWG OF M USKOKA FAIRYVIEW W ATER TREATMENT PLANT PROCESS MECHANICAL MB JPN ISSUED FOR TENDER 07/2012 0 PHASE I UPGRADES BAR IS 25mm ON APVD BY REVISION DATE NO. CONTRACT 12-432-253 PIPING MODIFICATIONS (2) ORIGINAL DRAWING. 0 25 MM APVD CHK DSGN DR 14of62 ET JPN JPN RC 2012/07/27 424251 000-D-2007 CH2M HILL 2012. ALL RIGHTS RESERVED. c THIS DOCUMENT, AND THE IDEAS AND DESIGNS INCORPORATED HEREIN, AS AN INSTRUMENT OF PROFESSIONAL SERVICE, IS THE PROPERTY OF CH2M HILL AND IS NOT TO BE USED, IN W HOLE OR IN PART, FOR ANY OTHER PROJECT WITHOUT THE W RITTEN AUTHORIZATION OF CH2MHILL. REUSE OF DOCUMENTS: ISSUED FOR TENDER
Page 1 and 2: SHEET NUMBER 00 000-G-0001 COVER SH
Page 3 and 4: A B C D 0330-105 CONT KEY ALL 15M@2
Page 5: A B C D NEW OPENING SAW-CUT LINE EX
Page 10 and 11: A B C D NOTES: 1 2 3 4 5 6 MATCH LI
Page 12 and 13: A B C D 300X200 RED TEE ON CONCRETE
Page 16 and 17: A B C D SST PIPE ENDS AS SHOWN ON P
Page 18 and 19: A B C D 1 2 3 4 5 6 PROVISIONAL ITE
Page 20 and 21: A B C D 1 2 3 4 5 6 HIGH LIFT PUMP
Page 22 and 23: A B C D REMOVE EXISTING NATURAL GAS
Page 24 and 25: A B C D EA (1650 L/s) MD-116 EMERGE
Page 26 and 27: A B C D 1 2 3 4 5 6 COMBUSTION AIR
Page 28 and 29: A B C D CHEMICAL CHEMICAL CHEMICAL
Page 30 and 31: A B C D 1 2 3 4 5 6 DATE PROJ VERIF
Page 32 and 33: A B C D HIGH LIFT PUMP ROOM REPLACE
Page 34 and 35: A B C D 1 2 3 4 5 6 1 EXISTING HIGH
Page 36 and 37: A B C D HIGH LIFT PUMP ROOM JANITOR
Page 38 and 39: A B C D CONNECT TO CUT AND CAP UP T
Page 40 and 41: A B C D AIR NOTES: FLOW 1 2 3 4 5 6
Page 42 and 43: A B C D SYMBOL DESCRIPTION SYMBOL D
Page 44 and 45: A B C D 1 2 3 4 5 6 MOTORIZED DAMPE
Page 46 and 47: A B C D 1 2 3 4 5 6 7 8 9 10 11 12
Page 48 and 49: A B C D NOTES: 1. 2. 3. 4. 5. 6. 7.
Page 50 and 51: A B C D NOTES: 1. EXISTING BACKGROU
Page 52 and 53: A B C D MISCELLANEOUS SYMBOLS SS T
Page 54 and 55: A B C D CHLORINE (OPTIONAL) POLYMER
Page 56 and 57: A B C D TO NEW SILO ACCESSORIES PLA
Page 58 and 59: A B C D 120V LP NAOH TANK FROM FROM
Page 60 and 61: A B C D NOTE: 120VAC L N C 120V AC
Page 62 and 63: A B C D 4’-6" 1. PRESSURE INDICAT

Drawings - Peak Engineering and Construction Ltd

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?