Sinclair 2013-A PDF - Brownells

Redding Neck Sizing
Bushings
#749-000-264
Holds 15
Redding,
Wilson or
Carbide
Bushings
73 Style Bushings:
Heat treated steel bushings. The sizing di am e ters
are hand polished with a surface hardness of Rc
60-62 to reduce sizing effort. Bushings are available
throughout the range of .185" thru .368" in
.001" increments. The last three digits of the part
denotes bushing size.
76 Style Bushings:
Heat treated steel bushings as above, but with the
addition of a Titanium Nitride coating to further
increase the effective surface hardness and reduce
sizing friction. Bushings are available throughout
the range of .185" thru .368" in .001" increments.
The last three digits of the part denotes bushing
size.
#RD73XXXSK 73 Style Bushings (Specify Size) $14.99
#RD76XXXSK 76 Style Bushings (Specify Size) 23.99
#749-000-264SK Redding Bushing Box 3.95
Determining
Redding Bushing Size
The proper bushing size can be easily determined
by measuring the outside neck diameter
of your loaded cartridges with a precision
micrometer or a dial caliper. Then, simply
subtract .001" from the cartridge that had the
smallest average neck diameter. This diameter
bushing will generally size case necks just
enough to create the proper press fit for the
bullet.
If you are using a Type “S” style die and not
turning the outside of your case necks, we suggest
using a bushing .002" smaller than your
smallest average neck diameter, and using the
expander ball included with your Type “S” die.
This size bushing will still give you minimal sizing
(maximizing the life of your brass) and the
expander ball will insure that each cartridge
has the same bullet grip.
Redding has found that when you have cases
with neck wall thicknesses on the thin side
of the SAAMI tolerance, your fired case will
measure considerably larger (.006" to .010"
larger) than your loaded rounds. In these circumstances,
Redding’s tests have shown that
a bushing .001" larger (than the loaded round)
may give you the desired bullet grip.
Redding Bushing Style Die Sets
Redding Dies
The different bushing style die sets that Redding offers are described below. If you need help in
selecting the set that would best serve your needs, please ask one of our sales reps for some advice.
All of the die sets listed below require the use of a neck sizing bushing. Information on bushings
can be found to the left.
Type “S” Bushing
Neck Die Set
This die set includes a Type “S” Bushing
Neck Die, a Body Die, and a Regular
Series Seater Die. Packaged in a
Redding Die Box with a wrench and
an extra decapping pin.
Category I $ 98.99
Category II 125.99
Category III 152.99
Type “S” Match
Full Length Die Set
Includes a Type “S” Bushing Full Length Sizing Die
and a Competition Series Bullet Seater. Packaged
in a Redding Die Box with a wrench and an extra
decapping pin. Excellent for semi-auto rifles.
Category I $145.99
Category II 177.99
Category III 216.99
Type “S” Match Neck
Die Set
This die set includes a Type “S” Bushing
Neck Die, a Body Die, and a
Competition Bullet Seater.
Packaged in a Redding Die
Box with a wrench and an
extra decapping pin.
Category I $170.99
Category II 208.99
Category III 253.99
Competition Neck Die Set
This die set includes a Competition Bushing Neck
Sizing Die, a Body Die, and a Competition Bullet
Seater. Packaged in a Redding Die Box with a
wrench.
Category I $215.99
Category II 259.99
Category III 320.99
Part numbers for sets
can be found on page 46
Type “S”
Match Full Length
Die Set
Competition
Neck Die Set
Type “S”
Bushing Neck
Die Set
Type “S”
Match Neck
Die Set
www.sinclairintl.com 45