Control Point® Addendum - DICKEY-john Corporation

More documents

Recommendations

Info

11001-1258-200311 Contents Tank Level Sensor................................................................................................2 Gate Height Sensor ..............................................................................................5 Road Temperature Sensor...................................................................................7 Air Temperature Sensor ......................................................................................9 Disable Servo .....................................................................................................10 12 Volt Switched Output .................................................................................... 11 Material Flow Alarm Label .................................................................................12 System Unit Additions .......................................................................................13 GSRS Mode .........................................................................................................13 Down Pressure Sensor ......................................................................................14 Bed Height Sensor .............................................................................................16 Material / Manual Selection Screen Updates ...................................................18 Harness Drawings ..............................................................................................19 Control Point version 6.40 software addendum 1
The purpose of this addendum is to describe the new features that have been implemented in Control Point® version 6.40 software. The new software can be downloaded into any Control Point unit; however the new software must have a new configuration that must be loaded with the new 6.40 compatible configuration tool. If the system configuration is a granular servo, spinner servo, or liquid pressure system, Control Point version 6.10 or newer software can not be used. The granular servo, spinner servo, and liquid pressure have been removed from these new versions of software. Some of the new features will require an adapter harness for them to interface with older harnesses. Contact your distributor or DICKEY-john support for information regarding the configuration tool and the adapter harnesses. Tank Level Sensor This sensor is used to monitor the liquid level for the pre-wet or anti-ice systems. The sensor is to be connected to the main harness with the lead labeled TANK or an adapter harness (466492040) that ties the tank level signal to pin 13 of the 16-pin granular valve connector on earlier versions of Control Point main harnesses. The tank level sensor feature must be enabled in the Control Point console before it will be active. It can be enabled for only one of the four liquid materials. The tank level will only be displayed when enabled and the selected material that it was enabled under is active. (I.E. If liquid 1 is set up for prewet (prewet yes) with tank level enabled and liquid 2 is anti ice (prewet no), the tank level will only be displayed when liquid 1 prewet is active. If the Control Point has been configured for use with anti-ice/prewet switch input on boom 5 to automatically switch between liquid 1 prewet and liquid 2 anti ice, the tank level will be displayed only when the switch is in the prewet mode. If the switch is in anti-ice mode, the tank level will not be displayed. If the tank level is desired for liquid 2, enable tank level under the liquid 2 configuration screen. Note: This will disable the tank level on liquid 1.) When the tank level is enabled, a bar graph with a digital percentage readout (Bargraph Yes) or an approximate material remaining readout will be displayed (Bargraph No). If granular is enabled, the spinner bar graph will share its portion of the operate screen with the tank level. If the tank level is disabled, the spinner bar graph will be displayed across the lower section of the operate screen. CONFIGURATION To enable the tank level sensor for a desired material, select Liquid Configuration (F5), then select material (1-4). The tank level option is the last item on the screen. The default for the tank level is NO. If NO is selected, the following screens will appear. 2 Control Point version 6.40 software addendum 11001-1258-200311
Page 1: Control Point ® Version 6.4 Addend
Page 5 and 6: TANK FULL This value can also be en
Page 7 and 8: The initial gate height screen has
Page 9 and 10: CONFIGURATION The initial road temp
Page 11 and 12: If YES, the following screen will a
Page 13 and 14: The 12V switched output works diffe
Page 15 and 16: If GSRS is YES the spinner configur
Page 17 and 18: CALIBRATION MIN PRESS This value ca
Page 19 and 20: Manual Entry Select the BED ALARM t
Page 21 and 22: Below is of the drawing for the new

Control Point® Addendum - DICKEY-john Corporation

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?